- 您現在的位置：買賣IC網 > PDF目錄371252 > X40421V14I-A Dual Voltage Monitor with Intergrated CPU Supervisor PDF資料下載
參數資料
| 型號： | X40421V14I-A |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Dual Voltage Monitor with Intergrated CPU Supervisor |
| 中文描述： | 雙電壓監視器集成CPU監控 |
| 文件頁數： | 9/25頁 |
| 文件大小： | 156K |
| 代理商： | X40421V14I-A |
LV2F, Low V2MON Reset Fail Bit (Volatile)
The LV2F bit will be set to “0” when V2MON falls below
V
TRIP2
.
X40420/X40421 – Preliminary
Characteristics subject to change without notice.
9 of 25
REV 1.2.14 7/12/02
www.xicor.com
Figure 7. Valid Data Changes on the SDA Bus
SCL
SDA
Data Stable
Data Change
Data Stable
At power-up, the Fault Detection Register is defaulted
to all “0”. The system needs to initialize this register to
all “1” before the actual monitoring take place. In the
event of any one of the monitored sources failed. The
corresponding bits in the register will change from a “1”
to a “0” to indicate the failure. At this moment, the sys-
tem should perform a read to the register and noted
the cause of the reset. After reading the register the
system should reset the register back to all “1” again.
The state of the Fault Detection Register can be read
at any time by performing a random read at address
0FFh, using the special preamble.
The FDR can be read by performing a random read at
0FFh address of the register at any time. Only one byte
of data is read by the register read operation.
MRF, Manual Reset Fail Bit (Volatile)
The MRF bit will set to “0” when Manual Reset input
goes active.
WDF, Watchdog Timer Fail Bit (Volatile)
The WDF bit will set to “0” when WDO goes active.
LV1F, Low V
CC
Reset Fail Bit (Volatile)
The LV1F bit will be set to “0” when V
CC
(V1MON) falls
below V
TRIP1
.
Interface Conventions
The device supports a bidirectional bus oriented proto-
col. The protocol defines any device that sends data
onto the bus as a transmitter, and the receiving device
as the receiver. The device controlling the transfer is
called the master and the device being controlled is
called the slave. The master always initiates data
transfers, and provides the clock for both transmit and
receive operations. Therefore, the devices in this family
operate as slaves in all applications.
Serial Clock and Data
Data states on the SDA line can change only during
SCL LOW. SDA state changes during SCL HIGH are
reserved for indicating start and stop conditions. See
Figure 7.
Serial Start Condition
All commands are preceded by the start condition,
which is a HIGH to LOW transition of SDA when SCL is
HIGH. The device continuously monitors the SDA and
SCL lines for the start condition and will not respond to
any command until this condition has been met. See
Figure 8.
Serial Stop Condition
All communications must be terminated by a stop condi-
tion, which is a LOW to HIGH transition of SDA when
SCL is HIGH. The stop condition is also used to place
the device into the Standby power mode after a read
sequence. A stop condition can only be issued after the
transmitting device has released the bus. See Figure 8.
相關PDF資料 |
PDF描述 |
|---|---|
| X40421V14I-B | Dual Voltage Monitor with Intergrated CPU Supervisor |
| X40421V14I-C | Dual Voltage Monitor with Intergrated CPU Supervisor |
| X40420S14-A | Dual Voltage Monitor with Intergrated CPU Supervisor |
| X40420S14-B | Dual Voltage Monitor with Intergrated CPU Supervisor |
| X40420S14-C | Dual Voltage Monitor with Intergrated CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X40421V14I-AT1 | 功能描述:IC VOLT MON DUAL SUP/SW 14-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40421V14I-B | 功能描述:IC VOLT MON DUAL SUP/SW 14-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40421V14I-BT1 | 功能描述:IC VOLT MON DUAL SUP/SW 14-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40421V14I-C | 功能描述:IC VOLT MON DUAL SUP/SW 14-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40421V14I-CT1 | 功能描述:IC VOLT MON DUAL SUP/SW 14-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。