- 您現在的位置：買賣IC網 > PDF目錄376442 > X40431S14Z-B (INTERSIL CORP) Triple Voltage Monitor with Integrated CPU Supervisor PDF資料下載
參數資料
| 型號： | X40431S14Z-B |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Triple Voltage Monitor with Integrated CPU Supervisor |
| 中文描述： | 3-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14 |
| 封裝： | 0.150 INCH, ROHS COMPLIANT, SOIC-14 |
| 文件頁數： | 11/26頁 |
| 文件大?。?/td> | 399K |
| 代理商： | X40431S14Z-B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
11
FN8251.1
May 24, 2006
Once set, WEL remains set until either it is reset to 0
(by writing a “0” to the WEL bit and zeroes to the other
bits of the control register) or until the part powers up
again. Writes to the WEL bit do not cause a high volt-
age write cycle, so the device is ready for the next
operation immediately after the stop condition.
BP: Block Protect Bits (Nonvolatile)
The Block Protect Bit BP, determines which blocks of
the array are write protected. A write to a protected
block of memory is ignored. The block protect bit will
prevent write operations to half or none of the array.
PUP1, PUP0: Power-up Bits (Nonvolatile)
The Power-up bits, PUP1 and PUP0, determine the
t
PURST
time delay. The nominal power-up times are
shown in the following table.
WD1, WD0: Watchdog Timer Bits (Nonvolatile)
The bits WD1 and WD0 control the period of the
Watchdog Timer. The options are shown below.
Writing to the Control Registers
Changing any of the nonvolatile bits of the control and
trickle registers requires the following steps:
– Write a 02H to the Control Register to set the Write
Enable Latch (WEL). This is a volatile operation, so
there is no delay after the write. (Operation pre-
ceded by a start and ended with a stop).
– Write a 06H to the Control Register to set the
Register Write Enable Latch (RWEL) and the WEL
bit. This is also a volatile cycle. The zeros in the data
byte are required. (Operation proceeded by a start
and ended with a stop).
– Write one byte value to the Control Register that has
all the control bits set to the desired state. The Control
register can be represented as
qxys
001
r
in binary,
where
xy
are the WD bits,
s
is the BP bit and
qr
are the
power-up bits. This operation proceeded by a start and
ended with a stop bit. Since this is a nonvolatile write
cycle it will take up to 10ms (max.) to complete. The
RWEL bit is reset by this cycle and the sequence must
be repeated to change the nonvolatile bits again. If bit
2 is set to ‘1’ in this third step (
qxys
011
r
) then the
RWEL bit is set, but the WD1, WD0, PUP1, PUP0, and
BP bits remain unchanged. Writing a second byte to
the control register is not allowed. Doing so aborts the
write operation and returns a NACK.
– A read operation occurring between any of the previ-
ous operations will not interrupt the register write
operation.
– The RWEL bit cannot be reset without writing to the
nonvolatile control bits in the control register, power
cycling the device or attempting a write to a write
protected block.
To illustrate, a sequence of writes to the device con-
sisting of [02H, 06H, 02H] will reset all of the nonvola-
tile bits in the Control Register to 0. A sequence of
[02H, 06H, 06H] will leave the nonvolatile bits
unchanged and the RWEL bit remains set.
Notes: 1. t
PURST
is set to 200ms as factory default.
2. Watch Dog Timer bits are shipped disabled.
FAULT DETECTION REGISTER
The Fault Detection Register (FDR) provides the user
the status of what causes the system reset active. The
Manual Reset Fail, Watchdog Timer Fail and Three
Low Voltage Fail bits are volatile
The FDR is accessed with a special preamble in the
slave byte (1011) and is located at address 0FFh. It
can only be modified by performing a byte write opera-
tion directly to the address of the register and only one
data byte is allowed for each register write operation.
There is no need to set the WEL or RWEL in the
control register to access this FDR.
BP
0
1
Protected Addresses
(Size)
None
100h – 1FFh (256 bytes)
Memory Array
Lock
None
Upper Half of
Memory Array
PUP1
PUP0
Power-on Reset Delay (
t
PURST
)
50ms
200ms (factory setting)
400ms
800ms
0
0
1
1
0
1
0
1
WD1
0
0
1
1
WD0
0
1
0
1
Watchdog Time Out Period
1.4 seconds
200 milliseconds
25 milliseconds
disabled (factory setting)
7
6
5
4
3
2
0
1
0
0
0
LV1F
LV2F
LV3F
WDF
MRF
X40430, X40431, X40434, X40435
相關PDF資料 |
PDF描述 |
|---|---|
| X40431V14IZ-B | Triple Voltage Monitor with Integrated CPU Supervisor |
| X40431V14Z-A | Triple Voltage Monitor with Integrated CPU Supervisor |
| X40431V14Z-B | Triple Voltage Monitor with Integrated CPU Supervisor |
| X40434 | Triple Voltage Monitor with Integrated CPU Supervisor |
| X40434S14IZ-A | Triple Voltage Monitor with Integrated CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X40431S14Z-BT1 | 制造商:Intersil Corporation 功能描述:PROCESSOR SUPERVISOR 4.4V/2.6V/1.7V 3000UA 14SOIC - Tape and Reel 制造商:Intersil Corporation 功能描述:Supervisory Circuits TRPL SUP 4K II2S LO VT1 4 4 VT2 2 6 VT3 |
| X40431V14-A | 功能描述:IC VOLT MON TRPL EEPROM 14-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40431V14-AT1 | 功能描述:IC VOLT MON TRPL EEPROM 14-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40431V14-B | 功能描述:IC VOLT MON TRPL EEPROM 14-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40431V14-BT1 | 功能描述:IC VOLT MON TRPL EEPROM 14-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。