- 您現在的位置：買賣IC網 > PDF目錄371254 > X4045M8IZ-2.7 (INTERSIL CORP) RTC Module With CPU Supervisor PDF資料下載
參數資料
| 型號： | X4045M8IZ-2.7 |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | RTC Module With CPU Supervisor |
| 中文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 封裝： | ROHS COMPLIANT, MSOP-8 |
| 文件頁數： | 9/25頁 |
| 文件大小： | 144K |
| 代理商： | X4045M8IZ-2.7 |
X4043/45
Characteristics subject to change without notice.
9 of 25
REV 1.1.17 9/14/01
www.xicor.com
stop condition is generated by the master, the device
will continue to transmit data. The device will terminate
further data transmissions if an acknowledge is not
detected. The master must then issue a stop condition
to return the device to standby mode and place the
device into a known state.
Figure 8. Acknowledge Response From Receiver
Data Output
from Transmitter
Data Output
from Receiver
8
1
9
Start
Acknowledge
SCL from
Master
X4043/45 ADDRESSING
Slave Address Byte
Following a start condition, the master must output a
slave address byte. This byte consists of several parts:
– a device type identifier that is ‘1010’ to access the
array and ‘1011’ to access the control register.
– two bits of ‘0’.
– one bit that becomes the MSB of the address.
– one bit of the slave command byte is a R/W bit. The
R/W bit of the slave address byte defines the opera-
tion to be performed. When the R/W bit is a one, then
a read operation is selected. A zero selects a write
operation. Refer to Figure 8.
– After loading the entire slave address byte from the
SDA bus, the device compares the input slave byte
data to the proper slave byte. Upon a correct compare,
the device outputs an acknowledge on the SDA line.
Word Address
The word address is either supplied by the master or
obtained from an internal counter. The internal counter
is undefined on a power up condition.
Slave Address Byte
Figure 9. X4043/45 Addressing
Operational Notes
The device powers-up in the following state:
– The device is in the low power standby state.
– The WEL bit is set to ‘0’. In this state it is not possible
to write to the device.
– SDA pin is the input mode.
– RESET signal is active for t
PURST
.
SERIAL WRITE OPERATIONS
Byte Write
For a write operation, the device requires the slave
address byte and a word address byte. This gives the
master access to any one of the words in the array.
After receipt of the word address byte, the device
responds with an acknowledge, and awaits the next
eight bits of data. After receiving the 8 bits of the data
byte, the device again responds with an acknowledge.
The master then terminates the transfer by generating a
stop condition, at which time the device begins the inter-
nal write cycle to the nonvolatile memory. During this
internal write cycle, the device inputs are disabled, so the
device will not respond to any requests from the master.
The SDA output is at high impedance. See Figure 10.
A write to a protected block of memory will suppress
the acknowledge bit.
Array
Control Reg.
1
1
0
0
1
1
0
1
0
0
A8
R/W
A7
A6
A5
A4
A3
A2
A1
A0
Word Address
Slave Byte
相關PDF資料 |
PDF描述 |
|---|---|
| X4045P-4.5A | RTC Module With CPU Supervisor |
| X4043M8I-2.7 | RTC Module With CPU Supervisor |
| X4045M8I-2.7 | RTC Module With CPU Supervisor |
| X4043M8I-2.7A | RTC Module With CPU Supervisor |
| X4045M8I-2.7A | RTC Module With CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X4045M8IZ-4.5A | 功能描述:IC CPU SUPERV 4K EEPROM 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:最小為 600 ms 電壓 - 閥值:3.8V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) |
| X4045M8Z | 功能描述:IC CPU SUPERV 4K EEPROM 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:最小為 600 ms 電壓 - 閥值:3.8V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) |
| X4045M8Z-2.7 | 功能描述:IC CPU SUPERV 4K EEPROM 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:最小為 600 ms 電壓 - 閥值:3.8V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) |
| X4045M8Z-2.7A | 功能描述:IC CPU SUPERV 4K EEPROM 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:最小為 600 ms 電壓 - 閥值:3.8V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) |
| X4045M8Z-4.5A | 功能描述:IC CPU SUPERV 4K EEPROM 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:最小為 600 ms 電壓 - 閥值:3.8V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。