- 您現在的位置：買賣IC網 > PDF目錄371255 > X4045PI (INTERSIL CORP) RTC Module With CPU Supervisor PDF資料下載
參數資料
| 型號： | X4045PI |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | RTC Module With CPU Supervisor |
| 中文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
| 封裝： | PLASTIC, DIP-8 |
| 文件頁數： | 4/25頁 |
| 文件大小： | 144K |
| 代理商： | X4045PI |
X4043/45
Characteristics subject to change without notice.
4 of 25
REV 1.1.17 9/14/01
www.xicor.com
Setting a V
There are two procedures used to set the threshold
voltages (V
TRIP
), depending if the threshold voltage to
be stored is higher or lower than the present value. For
example, if the present V
TRIP
V
TRIP
is 3.2 V, the new voltage can be stored directly
into the V
TRIP
cell. If however, the new setting is to be
lower than the present setting, then it is necessary to
“reset” the V
TRIP
voltage before setting the new value.
TRIP
Voltage
is 2.9 V and the new
Setting a Higher V
To set a V
higher than the present threshold, the user must apply
the desired V
TRIP
threshold voltage to the V
programming voltage (Vp) must be applied to the WP
pin before a START condition is set up on SDA. Next,
issue on the SDA pin the Slave Address A0h, followed
by the Byte Address 01h for V
Byte in order to program V
TRIP
a valid write operation initiates the programming
sequence. WP pin must then be brought LOW to com-
plete the operation.
TRIP
Voltage
TRIP
threshold to a new voltage which is
CC
. Then, a
TRIP
. The STOP bit following
and a 00h Data
To check if the V
the device. Slowly ramp up V
output, RESET (4043) or RESET (4045) switches. The
voltage at which this occurs is the V
Figure 2).
TRIP
has been set, first power down
and observe when the
CC
TRIP
(actual) (see
C
ASE
A
Now if the desired V
(actual), then add the difference between V
(desired) – V
TRIP
(actual) to the original V
This is your new V
TRIP
that should be applied to V
and the whole sequence should be repeated again
(see Figure 5).
TRIP
is greater than the V
TRIP
TRIP
TRIP
desired.
CC
C
ASE
B
Now if the V
(desired), perform the reset sequence as described in
the next section. The new V
to V
CC
will now be: V
TRIP
(desired) – (V
V
TRIP
(desired)).
Note:
This operation does not corrupt the memory
array.
TRIP
(actual), is higher than the V
TRIP
TRIP
voltage to be applied
TRIP
(actual) –
Setting a Lower V
In order to set V
present value, then V
ing to the procedure described below. Once V
been “reset”, then V
TRIP
age using the procedure described in “Setting a Higher
V
TRIP
Voltage”.
TRIP
Voltage
to a lower voltage than the
must first be “reset” accord-
TRIP
TRIP
TRIP
has
can be set to the desired volt-
Resetting the V
To reset a V
TRIP
voltage, apply the programming volt-
age (Vp) to the WP pin before a START condition is set
up on SDA. Next, issue on the SDA pin the Slave
Address A0h followed by the Byte Address 03h fol-
lowed by 00h for the Data Byte in order to reset V
TRIP
.
The STOP bit following a valid write operation initiates
the programming sequence. Pin WP must then be
brought LOW to complete the operation.
TRIP
Voltage
After being reset, the value of V
TRIP
becomes a nomi-
nal value of 1.7V or lesser.
Note:
This operation does not corrupt the memory
array.
相關PDF資料 |
PDF描述 |
|---|---|
| X4045PIZ | RTC Module With CPU Supervisor |
| X4045PZ | RTC Module With CPU Supervisor |
| X4043P | RTC Module With CPU Supervisor |
| X4043PZ | RTC Module With CPU Supervisor |
| X4043S8IZ-2.7A | RTC Module With CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X4045PI-2.7 | 功能描述:IC CPU SUPERV 4K EE RST HI 8DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:標準傳輸延遲為 60 µs 電壓 - 閥值:3V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:Digi-Reel® 其它名稱:LM8364BALMF30DKR |
| X4045PI-2.7A | 功能描述:IC SUPERVISOR CPU 4K EE 8-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X4045PI-4.5A | 功能描述:IC SUPERVISOR CPU 4K EE 8-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X4045PIZ | 功能描述:IC SUPERVISOR CPU 4K EE 8-DIP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:最小為 600 ms 電壓 - 閥值:3.8V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) |
| X4045PIZ-2.7 | 功能描述:IC SUPERVISOR CPU 4K EE 8-DIP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:最小為 600 ms 電壓 - 閥值:3.8V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。