參數資料
型號： X4283AP
元件分類： EEPROM
英文描述： CPU Supervisor with 128K EEPROM
中文描述： CPU監控與128K的EEPROM的
文件頁數： 8/22頁
文件大?。?/td> 412K
代理商： X4283AP
X4283/85 – Preliminary Information
Characteristics subject to change without notice.
8 of 22
REV 1.17 11/27/00
www.xicor.com
Serial Start Condition
All commands are preceded by the start condition,
which is a HIGH to LOW transition of SDA when SCL is
HIGH. The device continuously monitors the SDA and
SCL lines for the start condition and will not respond to
any command until this condition has been met. See
Figure 6.
Serial Stop Condition
All communications must be terminated by a stop
condition, which is a LOW to HIGH transition of SDA
when SCL is HIGH. The stop condition is also used to
place the device into the Standby power mode after a
read sequence. A stop condition can only be issued
after the transmitting device has released the bus. See
Figure 6.
Figure 6. Valid Start and Stop Conditions
SCL
SDA
Start
Stop
Serial Acknowledge
Acknowledge is a software convention used to indicate
successful data transfer. The transmitting device, either
master or slave, will release the bus after transmitting
eight bits. During the ninth clock cycle, the receiver will
pull the SDA line LOW to acknowledge that it received
the eight bits of data. Refer to Figure 7.
The device will respond with an acknowledge after rec-
ognition of a start condition and if the correct Device
Identifier and Select bits are contained in the Slave
Address Byte. If a write operation is selected, the
device will respond with an acknowledge after the
receipt of each subsequent eight bit word. The device
will acknowledge all incoming data and address bytes,
except for the Slave Address Byte when the Device
Identifier and/or Select bits are incorrect.
In the read mode, the device will transmit eight bits of
data, release the SDA line, then monitor the line for an
acknowledge. If an acknowledge is detected and no
stop condition is generated by the master, the device
will continue to transmit data. The device will terminate
further data transmissions if an acknowledge is not
detected. The master must then issue a stop condition
to return the device to Standby mode and place the
device into a known state.
Figure 7. Acknowledge Response from Receiver
Data Output
from Transmitter
Data Output
from Receiver
8
1
9
START
Acknowledge
SCL from
Master
相關PDF資料
PDF描述
X4283S8-2.7 CPU Supervisor with 128K EEPROM
X4283V8-2.7 CPU Supervisor with 128K EEPROM
X4283V8-4.5A CPU Supervisor with 128K EEPROM
X4283V8I-2.7A CPU Supervisor with 128K EEPROM
X4283S8 CPU Supervisor with 128K EEPROM
相關代理商/技術參數
參數描述
X4283F 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:CPU Supervisor with 128K EEPROM
X4283G 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:CPU Supervisor with 128K EEPROM
X4283I 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:CPU Supervisor with 128K EEPROM
X4283P 功能描述:IC SUPERVISOR CPU 128K EE 8-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件
X4283P-2.7 功能描述:IC SUPERVISOR CPU 128K EE 8-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*