- 您現在的位置：買賣IC網 > PDF目錄371257 > X4283S8I-2.7A (INTERSIL CORP) CPU Supervisor with 128K EEPROM PDF資料下載
參數資料
| 型號： | X4283S8I-2.7A |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | CPU Supervisor with 128K EEPROM |
| 中文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 封裝： | PLASTIC, SOIC-8 |
| 文件頁數： | 6/22頁 |
| 文件大?。?/td> | 412K |
| 代理商： | X4283S8I-2.7A |
X4283/85 – Preliminary Information
Characteristics subject to change without notice.
6 of 22
REV 1.17 11/27/00
www.xicor.com
The state of the Control Register can be read at any
time by performing a random read at address FFFFh.
Only one byte is read by each register read operation.
The X4283/85 resets itself after the first byte is read.
The master should supply a stop condition to be con-
sistent with the bus protocol, but a stop is not required
to end this operation.
RWEL: Register Write Enable Latch (Volatile)
The RWEL bit must be set to “1” prior to a write to the
Control Register.
WEL: Write Enable Latch (Volatile)
The WEL bit controls the access to the memory and to
the Register during a write operation. This bit is a vola-
tile latch that powers up in the LOW (disabled) state.
While the WEL bit is LOW, writes to any address,
including any control registers will be ignored (no
acknowledge will be issued after the Data Byte). The
WEL bit is set by writing a “1” to the WEL bit and zeroes
to the other bits of the control register. Once set, WEL
remains set until either it is reset to 0 (by writing a “0” to
the WEL bit and zeroes to the other bits of the control
register) or until the part powers up again. Writes to the
WEL bit do not cause a nonvolatile write cycle, so the
device is ready for the next operation immediately after
the stop condition.
BP2, BP1, BP0: Block Protect Bits (Nonvolatile)
The Block Protect Bits, BP2, BP1 and BP0, determine
which blocks of the array are write protected. A write to
a protected block of memory is ignored. The block pro-
tect bits will prevent write operations to one of eight
segments of the array.
WD1, WD0: Watchdog Timer Bits
The bits WD1 and WD0 control the period of the
Watchdog Timer. The options are shown below.
Write Protect Enable
These devices have an advanced Block Lock scheme
that protects one of eight blocks of the array when
enabled. It provides hardware write protection through
the use of a WP pin and a nonvolatile Write Protect
Enable (WPEN) bit. Four of the 8 protected blocks
match the original Block Lock segments and this pro-
tection scheme is fully compatible with the current
devices using 2 bits of block lock control (assuming the
BP2 bit is set to 0).
The Write Protect (WP) pin and the Write Protect
Enable (WPEN) bit in the Control Register control the
programmable Hardware Write Protect feature. Hard-
ware Write Protection is enabled when the WP pin and
the WPEN bit are HIGH and disabled when either the
WP pin or the WPEN bit is LOW. When the chip is Hard-
ware Write Protected, nonvolatile writes as well as to the
block protected sections in the memory array cannot be
written. Only the sections of the memory array that are
not block protected can be written. Note that since the
WPEN bit is write protected, it cannot be changed back
to a LOW state; so write protection is enabled as long
as the WP pin is held HIGH.
7
6
5
4
3
2
1
0
WPEN
WD1 WD0 BP1
BP0
RWEL
WEL BP2
B
B
B
Protected Addresses
(Size)
None (factory setting)
3000
h
- 3FFF
h
(4K bytes
)
2000
h
- 3FFF
h
(8K bytes
)
0000
h
- 3FFF
h
(16K bytes)
000
h
- 03F
h
(64 bytes)
000
h
- 07F
h
(128 bytes)
000
h
- 0FF
h
(256 bytes)
000
h
- 1FF
h
(512 bytes)
Array Lock
None
Upper 1/4 (Q4)
Upper 1/2 (Q3,Q4)
Full Array (All)
First Page (P1)
First 2 pgs (P2)
First 4 pgs (P4)
First 8 pgs (P8)
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
WD1
0
0
1
1
WD0
0
1
0
1
Watchdog Time Out Period
1.4 seconds (factory setting)
600 milliseconds
200 milliseconds
disabled
相關PDF資料 |
PDF描述 |
|---|---|
| X4283S8I-4.5A | CPU Supervisor with 128K EEPROM |
| X4283V8 | CPU Supervisor with 128K EEPROM |
| X4283V8-2.7 | CPU Supervisor with 128K EEPROM |
| X4283V8-2.7A | CPU Supervisor with 128K EEPROM |
| X4283V8-4.5A | CPU Supervisor with 128K EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X4283S8I-4.5A | 功能描述:IC SUPERVISOR CPU 128K EE 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X4283S8IZ | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CPU Supervisor with 128K EEPROM |
| X4283S8IZ-2.7 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CPU Supervisor with 128K EEPROM |
| X4283S8IZ-2.7A | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CPU Supervisor with 128K EEPROM |
| X4283S8Z | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CPU Supervisor with 128K EEPROM |
發布緊急采購，3分鐘左右您將得到回復。