- 您現在的位置：買賣IC網 > PDF目錄371261 > X5083S8I RTC Module With CPU Supervisor PDF資料下載
參數資料
| 型號： | X5083S8I |
| 元件分類： | CPU監測 |
| 英文描述： | RTC Module With CPU Supervisor |
| 中文描述： | 時鐘模塊CPU監控 |
| 文件頁數： | 3/21頁 |
| 文件大?。?/td> | 115K |
| 代理商： | X5083S8I |
X5083
Characteristics subject to change without notice.
3 of 21
REV 1.1.6 6/25/02
www.xicor.com
PRINCIPLES OF OPERATION
Power On Reset
Application of power to the X5083 activates a power on
reset circuit. This circuit goes LOW at 1V and pulls the
RESET pin active. This signal prevents the system
microprocessor from starting to operate with insuffi-
cient voltage or prior to stabilization of the oscillator.
RESET active also blocks communication to the device
through the SPI interface. When V
device V
TRIP
value for 200ms (nominal) the circuit
releases RESET, allowing the processor to begin exe-
cuting code. While V
CC
< V
TRIP
device are inhibited.
CC
exceeds the
communications to the
Low Voltage Monitoring
During operation, the X5083 monitors the V
and asserts RESET if supply voltage falls below a pre-
set minimum V
TRIP
. The RESET signal prevents the
microprocessor from operating in a power fail or
brownout condition and terminates any SPI communi-
cation in progress. The RESET signal remains active
until the voltage drops below 1V. It also remains active
until V
CC
returns and exceeds V
CC
level
TRIP
for 200ms.
When V
progress are terminated and communications are
inhibited until V
CC
exceeds V
CC
falls below V
TRIP
, any communications in
TRIP
for t
PURST
.
Watchdog Timer
The watchdog timer circuit monitors the microprocessor
activity by monitoring the WDI input. The microprocessor
must toggle the CS/WDI pin periodically to prevent a
RESET signal. The CS/WDI pin must be toggled from
HIGH to LOW prior to the expiration of the watchdog time
out period. The state of two nonvolatile control bits in the
status register determine the watchdog timer period. The
microprocessor can change these watchdog bits with no
action taken by the microprocessor these bits remain
unchanged, even after total power failure.
V
The X5083 is shipped with a standard V
(V
TRIP
) voltage. This value will not change over normal
operating and storage conditions. However, in applica-
tions where the standard V
TRIP
higher precision is needed in the V
X5083 threshold may be adjusted. The procedure is
described below, and uses the application of a high
voltage control signal.
CC
Threshold Reset Procedure
CC
threshold
is not exactly right, or if
TRIP
value, the
Setting the V
This procedure is used to set the V
voltage value. For example, if the current V
and the new V
TRIP
is 4.6V, this procedure will directly
make the change. If the new setting is to be lower than
the current setting, then it is necessary to reset the trip
point before setting the new value.
TRIP
Voltage
TRIP
to a higher
TRIP
is 4.4V
To set the new V
threshold voltage to the V
the programming voltage V
mand, followed by a write of Data 00h to address 01h.
CS going HIGH on the write operation initiates the
V
TRIP
programming sequence. Bring WP LOW to com-
plete the operation.
TRIP
voltage, apply the desired V
CC
pin and tie the WP pin to
P
. Then send a WREN com-
TRIP
Note:
01h.
This operation also writes 00h to array address
Figure 1. Set V
TRIP
Level Sequence (V
CC
= desired V
TRIP
value)
0
1
2 3
4
5 6
7
SCK
SI
CS
06h
WREN
0
1
2 3
4
5 6
7 8
9 10
20 21 22 23
16 Bits
0001h
Address
02h
Write
WP
V
P
= 15-18V
00h
Data
相關PDF資料 |
PDF描述 |
|---|---|
| X5083S8I-2.7 | RTC Module With CPU Supervisor |
| X5083S8I-2.7A | RTC Module With CPU Supervisor |
| X5083S8 | RTC Module With CPU Supervisor |
| X5083S8-2.7 | RTC Module With CPU Supervisor |
| X5083S8-2.7A | RTC Module With CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X5083S8I-2.7 | 功能描述:IC CPU SUPRV 8K EE RST LO 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:標準傳輸延遲為 60 µs 電壓 - 閥值:3V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:Digi-Reel® 其它名稱:LM8364BALMF30DKR |
| X5083S8I-2.7A | 功能描述:IC SUPERVISOR CPU 8K EE 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:推挽式，圖騰柱 復位:低有效 復位超時:最小 145 ms 電壓 - 閥值:2.64V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WQFN 裸露焊盤 供應商設備封裝:16-TQFN-EP（4x4） 包裝:帶卷 (TR) |
| X5083S8I-2.7T2 | 功能描述:IC SUPERVISOR CPU 8K EE 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:推挽式，圖騰柱 復位:低有效 復位超時:最小 145 ms 電壓 - 閥值:2.64V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WQFN 裸露焊盤 供應商設備封裝:16-TQFN-EP（4x4） 包裝:帶卷 (TR) |
| X5083S8I-4.5A | 功能描述:IC SUPERVISOR CPU 8K EE 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:推挽式，圖騰柱 復位:低有效 復位超時:最小 145 ms 電壓 - 閥值:2.64V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WQFN 裸露焊盤 供應商設備封裝:16-TQFN-EP（4x4） 包裝:帶卷 (TR) |
| X5083S8I-4.5AT1 | 功能描述:IC SUPERVISOR CPU 8K EE 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:推挽式，圖騰柱 復位:低有效 復位超時:最小 145 ms 電壓 - 閥值:2.64V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WQFN 裸露焊盤 供應商設備封裝:16-TQFN-EP（4x4） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。