- 您現在的位置：買賣IC網 > PDF目錄297797 > X5323S8I-4.5A-T1 (INTERSIL CORP) 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 PDF資料下載
參數資料
| 型號： | X5323S8I-4.5A-T1 |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 封裝： | PLASTIC, SOIC-8 |
| 文件頁數： | 19/20頁 |
| 文件大?。?/td> | 341K |
| 代理商： | X5323S8I-4.5A-T1 |
8
FN8131.2
June 30, 2008
.
The watchdog timer bits, WD0 and WD1, select the
watchdog time out period. These nonvolatile bits are
programmed with the WRSR instruction.
The FLAG bit shows the status of a volatile latch that can be
set and reset by the system using the SFLB and RFLB
instructions. The flag bit is automatically reset upon
power-up. This flag can be used by the system to determine
whether a reset occurs as a result of a watchdog time out or
power failure.
Note: The Watch Dog Timer is shipped disabled. (WD1 = 1,
WD0 = 1. The factory default for Memory Block Protection is
‘None’. (BL1 = 0, BL0 = 0).
The nonvolatile WPEN bit is programmed using the WRSR
instruction. This bit works in conjunction with the WP pin to
provide an in-circuit programmable ROM function (Table 2). WP
is LOW and WPEN bit programmed HIGH disables all status
register write operations.
In Circuit Programmable ROM Mode
This mechanism protects the block lock and watchdog bits
from inadvertent corruption.
In the locked state (programmable ROM mode) the WP pin is
LOW and the nonvolatile bit WPEN is “1”. This mode disables
nonvolatile writes to the device’s status register.
Setting the WP pin LOW while WPEN is a “1” while an
internal write cycle to the status register is in progress will
not stop this write operation, but the operation disables
subsequent write attempts to the status register.
When WP is HIGH, all functions, including nonvolatile writes
to the status register operate normally. Setting the WPEN bit
in the status register to “0” blocks the WP pin function,
allowing writes to the status register when WP is HIGH or
LOW. Setting the WPEN bit to “1” while the WP pin is LOW
activates the programmable ROM mode, thus requiring a
change in the WP pin prior to subsequent status register
changes. This allows manufacturing to install the device in a
system with WP pin grounded and still be able to program
the status register. Manufacturing can then load
configuration data, manufacturing time and other parameters
into the EEPROM, then set the portion of memory to be
protected by setting the block lock bits, and finally set the
“OTP mode” by setting the WPEN bit. Data changes now
require a hardware change.
Read Sequence
When reading from the EEPROM memory array, CS is first
pulled low to select the device. The 8-bit READ instruction is
transmitted to the device, followed by the 16-bit address.
After the READ opcode and address are sent, the data
stored in the memory at the selected address is shifted out
on the SO line. The data stored in memory at the next
address can be read sequentially by continuing to provide
clock pulses. The address is automatically incremented to
the next higher address after each byte of data is shifted out.
STATUS
REGISTER BITS
ARRAY ADDRESSES PROTECTED
BL1
BL0
X5323/X5325
0
None (factory default)
0
1
$0C00 to $0FFF
1
0
$0800 to $0FFF
1
$0000 to $0FFF
STATUS REGISTER BITS
WATCHDOG TIME-OUT
(TYPICAL)
WD1
WD0
0
1.4s
0
1
600ms
1
0
200ms
1
disabled (factory default)
0
1
2
3
4
5
6
7
8
9
10
20
21
22
23
24
25
26
27
28
29
30
7
6
543
21
0
DATA OUT
CS
SCK
SI
SO
MSB
HIGH IMPEDANCE
INSTRUCTION
16-BIT ADDRESS
15
14
13
3
2
1
0
FIGURE 5. READ EEPROM ARRAY SEQUENCE
X5323, X5325
相關PDF資料 |
PDF描述 |
|---|---|
| X5323V14Z-2.7-T1 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14 |
| X5323S8Z-2.7A-T1 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| X5325S8I-2.7A | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| X5323V14 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14 |
| X5323V14I-2.7T1 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X5323S8IT1 | 功能描述:IC SUPERVISOR CPU 32K EE 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:推挽式，圖騰柱 復位:低有效 復位超時:最小 145 ms 電壓 - 閥值:2.64V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WQFN 裸露焊盤 供應商設備封裝:16-TQFN-EP（4x4） 包裝:帶卷 (TR) |
| X5323S8IZ | 功能描述:監控電路 CPU SUP/WDT 32K SPI EE RST LW 5V+/-10% RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| X5323S8IZ-2.7 | 功能描述:監控電路 CPU SUP/WDT 32K SPI EE RST LW 2 7-3 6V RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| X5323S8IZ-2.7A | 功能描述:監控電路 CPU SUP/WDT 32K SPI EE RST LW 2 7-3 6V RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| X5323S8IZ-2.7AT1 | 功能描述:監控電路 CPU SUP/WDT 32K SPI EE RST LW 2 7-3 6V RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。