- 您現在的位置：買賣IC網 > PDF目錄372535 > X5328 RTC Module With CPU Supervisor PDF資料下載
參數資料
| 型號： | X5328 |
| 元件分類： | CPU監測 |
| 英文描述： | RTC Module With CPU Supervisor |
| 中文描述： | 時鐘模塊CPU監控 |
| 文件頁數： | 3/22頁 |
| 文件大?。?/td> | 126K |
| 代理商： | X5328 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁
X5328/X5329
3
PRINCIPLES OF OPERATION
POWER ON RESET
Application of power to the X5328/X5329 activates a
Power On Reset Circuit. This circuit goes active at about
1V and pulls the RESET/RESET pin active. This signal
prevents the system microprocessor from starting to oper-
ate with insufficient voltage or prior to stabilization of the
oscillator. When Vcc exceeds the device V
200ms (nominal) the circuit releases RESET/RESET,
allowing the processor to begin executing code.
TRIP
value for
LOW VOLTAGE MONITORING
During operation, the X5328/X5329 monitors the V
level and asserts RESET/RESET if supply voltage falls
below a preset minimum V
TRIP
nal prevents the microprocessor from operating in a
power fail or brownout condition. The RESET/RESET sig-
nal remains active until the voltage drops below 1V. It also
remains active until Vcc returns and exceeds V
200ms.
CC
. The RESET/RESET sig-
TRIP
for
VCC THRESHOLD RESET PROCEDURE
The X5328/X5329 has a standard Vcc threshold (V
voltage. This value will not change over normal operating
and storage conditions. However, in applications where
the standard V
TRIP
is not exactly right, or for higher preci-
sion in the V
TRIP
value, the X5328/X5329 threshold may
be adjusted.
TRIP
)
Setting the V
This procedure sets the V
For example, if the current V
V
TRIP
is 4.6V, this procedure directly makes the change. If
the new setting is lower than the current setting, then it is
necessary to reset the trip point before setting the new
value.
TRIP
Voltage
TRIP
to a higher voltage value.
TRIP
is 4.4V and the new
To set the new V
threshold to the Vcc pin and tie the CS pin and the WP pin
HIGH. RESET/RESET and SO pins are left unconnected.
Then apply the programming voltage Vp to both SCK and
SI and pulse CS LOW then HIGH. Remove Vp and the
sequence is complete.
TRIP
voltage, apply the desired V
TRIP
Figure 1. Set V
TRIP
Voltage
Resetting the V
This procedure sets the V
For example, if the current V
reset, the new V
procedure must be used to set the voltage to a lower
value.
TRIP
Voltage
TRIP
TRIP
to a “native” voltage level.
is 4.4V and the V
is something less than 1.7V. This
TRIP
is
TRIP
To reset the V
and 5.5V to the Vcc pin. Tie the CS pin, the WP pin, and
the SCK pin HIGH. RESET/RESET and SO pins are left
unconnected. Then apply the programming voltage Vp to
the SI pin ONLY and pulse CS LOW then HIGH. Remove
Vp and the sequence is complete.
TRIP
voltage, apply a voltage between 2.7
Figure 2. Reset V
TRIP
Voltage
SCK
SI
Vp
Vp
CS
SCK
SI
Vcc
Vp
CS
相關PDF資料 |
PDF描述 |
|---|---|
| X5329 | RTC Module With CPU Supervisor |
| X55020 | Dual Voltage Monitor with Integrated System Battery Switch and EEPROM(帶集成化系統電池轉換和EEPROM的雙電壓監控器) |
| X5643(中文) | RTC Module With CPU Supervisor |
| X5643 | RTC Module With CPU Supervisor |
| X5645 | RTC Module With CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X532858IZ-2.7T1 | 制造商:Intersil Corporation 功能描述: |
| X5328P | 功能描述:IC SUPERVISOR CPU 32K EE 8-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:推挽式，圖騰柱 復位:低有效 復位超時:最小 145 ms 電壓 - 閥值:2.64V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WQFN 裸露焊盤 供應商設備封裝:16-TQFN-EP（4x4） 包裝:帶卷 (TR) |
| X5328P-2.7 | 功能描述:IC SUPERVISOR CPU 32K EE 8-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:推挽式，圖騰柱 復位:低有效 復位超時:最小 145 ms 電壓 - 閥值:2.64V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WQFN 裸露焊盤 供應商設備封裝:16-TQFN-EP（4x4） 包裝:帶卷 (TR) |
| X5328P-2.7A | 功能描述:IC SUPERVISOR CPU 32K EE 8-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:推挽式，圖騰柱 復位:低有效 復位超時:最小 145 ms 電壓 - 閥值:2.64V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WQFN 裸露焊盤 供應商設備封裝:16-TQFN-EP（4x4） 包裝:帶卷 (TR) |
| X5328P-4.5A | 功能描述:IC SUPERVISOR CPU 32K EE 8-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:推挽式，圖騰柱 復位:低有效 復位超時:最小 145 ms 電壓 - 閥值:2.64V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WQFN 裸露焊盤 供應商設備封裝:16-TQFN-EP（4x4） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。