- 您現在的位置：買賣IC網 > PDF目錄371268 > X5643S8I-4.5A SPI Serial EEPROM with Supervisory Features PDF資料下載
參數資料
| 型號： | X5643S8I-4.5A |
| 元件分類： | EEPROM |
| 英文描述： | SPI Serial EEPROM with Supervisory Features |
| 中文描述： | SPI串行EEPROM，帶有監控功能 |
| 文件頁數： | 5/22頁 |
| 文件大?。?/td> | 106K |
| 代理商： | X5643S8I-4.5A |
X5643/X5645
Characteristics subject to change without notice.
5 of 22
Figure 4. Sample V
TRIP
Reset Circuit
X5643/45
1
2
3
4
8
7
6
5
V
TRIP
Adj.
Program
NC
NC
V
P
Reset V
TRIP
Test
V
TRIP
Set V
TRIP
NC
RESET
4.7K
4.7K
10K
10K
+
SPI SERIAL MEMORY
The memory portion of the device is a CMOS serial
EEPROM array with Xicor’s block lock protection. The
array is internally organized as x 8. The device features
a Serial Peripheral Interface (SPI) and software proto-
col allowing operation on a simple four-wire bus.
The device utilizes Xicor’s proprietary Direct Write
cell, providing a minimum endurance of 100,000 cycles
and a minimum data retention of 100 years.
The device is designed to interface directly with the
synchronous Serial Peripheral Interface (SPI) of many
popular microcontroller families. It contains an 8-bit
instruction register that is accessed via the SI input,
with data being clocked in on the rising edge of SCK.
CS must be LOW during the entire operation.
All instructions (Table 1), addresses and data are trans-
ferred MSB first. Data input on the SI line is latched on
the first rising edge of SCK after CS goes LOW. Data is
output on the SO line by the falling edge of SCK. SCK is
static, allowing the user to stop the clock and then start it
again to resume operations where left off.
Write Enable Latch
The device contains a write enable latch. This latch
must be SET before a write operation is initiated. The
WREN instruction will set the latch and the WRDI
instruction will reset the latch (Figure 3). This latch is
automatically reset upon a power-up condition and
after the completion of a valid Write Cycle.
Status Register
The RDSR instruction provides access to the status regis-
ter. The status register may be read at any time, even dur-
ing a write cycle. The status register is formatted as follows:
The Write-In-Progress (WIP) bit is a volatile, read only
bit and indicates whether the device is busy with an
internal nonvolatile write operation. The WIP bit is read
using the RDSR instruction. When set to a “1”, a non-
volatile write operation is in progress. When set to a
“0”, no write is in progress.
7
6
5
4
3
2
1
0
WPEN
FLB
WD1
WD0
BL1
BL0
WEL
WIP
Table 1. Instruction Set
Notes:
*Instructions are shown MSB in leftmost position. Instructions are transferred MSB first.
Instruction Name
WREN
SFLB
WRDI/RFLB
RSDR
WRSR
READ
WRITE
Instruction Format*
0000 0110
0000 0000
0000 0100
0000 0101
0000 0001
0000 0011
0000 0010
Operation
Set the write enable latch (enable write operations)
Set flag bit
Reset the write enable latch/reset flag bit
Read status register
Write status register (watchdog, block lock, WPEN & flag bits)
Read data from memory array beginning at selected address
Write data to memory array beginning at selected address
相關PDF資料 |
PDF描述 |
|---|---|
| X5645S14-1.8 | SPI Serial EEPROM with Supervisory Features |
| X5643S8-1.8 | SPI Serial EEPROM with Supervisory Features |
| X5645S8-1.8 | SPI Serial EEPROM with Supervisory Features |
| X5645S8-2.7 | SPI Serial EEPROM with Supervisory Features |
| X5643P | RTC Module With CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X5645 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:CPU Supervisor with 64Kbit SPI EEPROM |
| X5645P | 功能描述:IC CPU SUPRV 64K EE RST HI 8DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:標準傳輸延遲為 60 µs 電壓 - 閥值:3V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:Digi-Reel® 其它名稱:LM8364BALMF30DKR |
| X5645P-4.5A | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:CPU Supervisor with 64Kbit SPI EEPROM |
| X5645S14 | 功能描述:IC CPU SUPRV 64K EE RST HI SO14 RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:標準傳輸延遲為 60 µs 電壓 - 閥值:3V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:Digi-Reel® 其它名稱:LM8364BALMF30DKR |
| X5645S14-1.8 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM with Supervisory Features |
發布緊急采購，3分鐘左右您將得到回復。