- 您現在的位置：買賣IC網 > PDF目錄371269 > X76F041PE-3 PASS TM SecureFlash PDF資料下載
參數資料
| 型號： | X76F041PE-3 |
| 英文描述： | PASS TM SecureFlash |
| 中文描述： | 密碼商標SecureFlash |
| 文件頁數： | 3/21頁 |
| 文件大小： | 107K |
| 代理商： | X76F041PE-3 |
X76F041
3
DEVICE OPERATION
There are three primary modes of operation for the
X76F041; READ, WRITE and CONFIGURATION. The
READ and WRITE modes may be performed with or
without an 8-byte password. The CONFIGURATION
mode always requires an 8-byte password.
The basic method of communication is established by
first enabling the device (CS LOW), generating a start
condition and then transmitting a command and address
field followed by the correct password (if configured to
require a password). All parts will be shipped from the
factory in the non-password mode. The user must per-
form an ACK Polling routine to determine the validity of
the password and start the data transfer (see Acknowl-
edge Polling). Only after the correct password is
accepted and an ACK Polling has been performed can
the data transfer occur.
To ensure correct communication, RST must remain
LOW under all conditions except when initiating a
“Response to Reset sequence”.
Figure 1. X76F041 Device Operation
Data is transferred in 8-bit segments, with each transfer
being followed by an ACK, generated by the receiving
device.
If the X76F041 is in a nonvolatile write cycle a “no ACK”
(SDA HIGH) response will be issued in response to load-
ing of the command + high order address byte. If a stop
condition is issued prior to the nonvolatile write cycle the
write operation will be terminated and the part will reset
and enter into a standby mode.
The basic sequence is illustrated in Figure 1.
After each transaction is completed, the X76F041 will
reset and enter into a standby mode. This will also be the
response if an attempt is made to access any limited
array.
Password Registers
The three passwords, Read, Write and Configuration
are stored in three 64 bit Write Only registers as illus-
trated in figure 2.
Figure 2. Password Registers
Device Configuration
Five 8-Bit configuration registers are used to configure
the X76F041. These are shown in figure 3.
Figure 3. Configuration Registers
LOAD
LOW ORDER ADDRESS / CONFIGURATION INSTRUCTION
BYTE
LOAD 8–BYTE PASSWORD
(IF APPLICABLE)
VERIFY PASSWORD ACCEPTANCE BY USE
OF ACK POLLING (IF APPLICABLE)
READ / WRITE
DATA BYTES
LOAD
COMMAND+HIGH ORDER ADDRESS
BYTE
7002 ILL F03
64 BIT WRITE PASSWORD
64 BIT READ PASSWORD
64 BIT CONFIGURATION PASSWORD
63
0
7002 ILL F04
ACR1
ACR2
CR
RR
RC
RES
RES
RES
RESERVED
RETRY REGISTER
CONFIGURATION REGISTER
ARRAY CONTROL REGISTER 2
ARRAY CONTROL REGISTER 1
RETRY COUNTER
7002 ILL F04B
63
0
相關PDF資料 |
PDF描述 |
|---|---|
| X76F041WE-3 | PASS TM SecureFlash |
| X76F041A | PASS TM SecureFlash |
| X76F041A-3 | PASS TM SecureFlash |
| X76F041AE | PASS TM SecureFlash |
| X76F041H | PASS TM SecureFlash |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X76F041W | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:PASS TM SecureFlash |
| X76F041W-3 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:PASS TM SecureFlash |
| X76F041WE | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:PASS TM SecureFlash |
| X76F041WE-3 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:PASS TM SecureFlash |
| X76F100 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:1K 128 x 8 Bit |
發布緊急采購，3分鐘左右您將得到回復。