- 您現在的位置：買賣IC網 > PDF目錄371269 > X76F100PI 1K 128 x 8 Bit PDF資料下載
參數資料
| 型號： | X76F100PI |
| 英文描述： | 1K 128 x 8 Bit |
| 中文描述： | 每1000 128 × 8位 |
| 文件頁數： | 4/17頁 |
| 文件大?。?/td> | 275K |
| 代理商： | X76F100PI |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
X76F100
Characteristics subject to change without notice.
4 of 16
REV 1.0 6/22/00
www.xicor.com
Figure 2. Data Validity
Figure 3. Definition of Start and Stop Conditions
Table 1. X76F100 Instruction Set
Command after Start
1 0 0 S
3
S
1 0 0 S
3
S
1 1 1 1 1 1 0 0
1 1 1 1 1 1 1 0
0 1 0 1 0 1 0 1
Command Description
Sector Write
Sector Read
Change Write Password
Change Read Password
Password ACK Command
Password Used
Write
Read
Write
Write
None
2
S
S
1
S
S
0
0
1
2
1
0
SCL
SDA
Data Stable
Data
Change
SCL
SDA
Start Condition
Stop Condition
Illegal command codes will be disregarded. The part
will respond with a “no-ACK” to the illegal byte and
then return to the standby mode. All write/read opera-
tions require a password.
PROGRAM OPERATIONS
Sector Write
The sector write mode requires issuing the 8-bit write
command followed by the password and then the data
bytes transferred as illustrated in Figure 4. The write
command byte contains the address of the sector to be
written. Data is written starting at the first address of a
sector and eight bytes must be transferred. After the
last byte to be transferred is acknowledged a stop con-
dition is issued which starts the nonvolatile write cycle.
If more or less than 8-bytes are transferred, the data in
the sector remains unchanged.
ACK Polling
Once a stop condition is issued to indicate the end of
the host’s write sequence, the X76F100 initiates the
internal nonvolatile write cycle. In order to take advan-
tage of the typical 5ms write cycle, ACK polling can
begin immediately. This involves issuing the start con-
dition followed by the new command code of 8-bits (1st
byte of the protocol.) If the X76F100 is still busy with
the nonvolatile write operation, it will issue a “no-ACK”
in response. If the nonvolatile write operation has com-
pleted, an “ACK” will be returned and the host can then
proceed with the rest of the protocol.
相關PDF資料 |
PDF描述 |
|---|---|
| X76F100PI-3.0 | 1K 128 x 8 Bit |
| X76F100S8 | 1K 128 x 8 Bit |
| X76F100S8-3.0 | 1K 128 x 8 Bit |
| X76F100S8I | CLAMP |
| X76F100S8I-3.0 | 1K 128 x 8 Bit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X76F100PI-3.0 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:1K 128 x 8 Bit |
| X76F100S8 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:1K 128 x 8 Bit |
| X76F100S8-3.0 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:1K 128 x 8 Bit |
| X76F100S8I | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:1K 128 x 8 Bit |
| X76F100S8I-3.0 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:1K 128 x 8 Bit |
發布緊急采購，3分鐘左右您將得到回復。