- 您現在的位置：買賣IC網 > PDF目錄371277 > X9110TV14I-2.7 CLAMP PDF資料下載
參數資料
| 型號： | X9110TV14I-2.7 |
| 英文描述： | CLAMP |
| 中文描述： | 單數字控制（數字電位器）電位 |
| 文件頁數： | 6/21頁 |
| 文件大小： | 133K |
| 代理商： | X9110TV14I-2.7 |
X9110 – Preliminary Information
Characteristics subject to change without notice.
6 of 21
REV 1.1.4 11/13/00
www.xicor.com
Table 1. Wiper Control Register, WCR (10-bit), WCR9–WCR0:
Used to store the current wiper position (Volatile, V)
Table 2. Data Register, DR (10-bit), Bit 9–Bit 0:
Used to store wiper positions or data (Non-Volatile, NV)
Table 3. Status Register, SR (1-bit)
WCR9
V
(MSB)
WCR8
V
WCR7
V
WCR6
V
WCR5
V
WCR4
V
WCR3
V
WCR2
V
WCR1
V
WCR0
V
(LSB)
Bit 9
NV
MSB
Bit 8
NV
Bit 7
NV
Bit 6
NV
Bit 5
NV
Bit 4
NV
Bit 3
NV
Bit 2
NV
Bit 1
NV
Bit 0
NV
LSB
WIP
(LSB)
DEVICE INSTRUCTIONS
Identification Byte (ID and A)
The first byte sent to the X9110 from the host, following
a CS going HIGH to LOW, is called the Identification
Byte. The most significant four bits of the slave address
are a device type identifier. The ID[3:0] bits is the
device ID for the X9110; this is fixed as 0101[B] (refer
to Table 4).
The A0 bit in the ID byte is the internal slave address.
The physical device address is defined by the state of
the A0 input pin. The slave address is externally
specified by the user. The X9110 compares the serial
data stream with the address input state; a successful
compare of the address bit is required for the X9110 to
successfully continue the command sequence. Only
the device whose slave address matches the incoming
device address sent by the master executes the
instruction. The A0 input can be actively driven by
CMOS input signals or tied to V
CC
or V
SS
. The R/W bit
is used to set the device to either read or write mode.
Instruction Byte and Register Selection
The next byte sent to the X9110 contains the
instruction and register pointer information. The three
most significant bits are used provide the instruction
opcode (I[2:0]). The RB and RA bits point to one of the
four registers. The format is shown in Table 5.
Table 4. Identification Byte Format
Table 5. Instruction Byte Format
ID3
0
(MSB)
ID2
1
ID1
0
ID0
1
0
0
A0
R/W
(LSB)
Device Type
Identifier
Internal Slave
Address
Read or
Write Bit
I2
I1
I0
0
RB
RA
0
0
(MSB)
(LSB)
Instruction
Opcode
Register
Selection
RB
0
0
1
1
RA
0
1
0
1
Register
DR0
DR1
DR2
DR3
相關PDF資料 |
PDF描述 |
|---|---|
| X9110TV14 | 240 x 128 pixel format, LED or EL Backlight |
| X9110TV14IZ-2.7 | Single Digitally-Controlled (XDCP) Potentiometer |
| X9110TV14Z | Single Digitally-Controlled (XDCP) Potentiometer |
| X9110TV14Z-2.7 | Connector assemblies |
| X9110 | Single Digitally-Controlled (XDCP) Potentiometer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9110TV14IZ | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9110TV14IZ-2.7 | 功能描述:IC POT DGTL 100K OHM 14-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT |
| X9110TV14IZ-2.7T1 | 功能描述:IC XDCP 1024-TAP 100K 14-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9110TV14Z | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9110TV14Z-2.7 | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。