- 您現在的位置：買賣IC網 > PDF目錄371277 > X9111TV14I Single Digitally-Controlled Potentiometer PDF資料下載
參數資料
| 型號： | X9111TV14I |
| 元件分類： | 數字電位計 |
| 英文描述： | Single Digitally-Controlled Potentiometer |
| 中文描述： | 單數字控制電位器 |
| 文件頁數： | 4/21頁 |
| 文件大小： | 156K |
| 代理商： | X9111TV14I |
X9111 – Preliminary Information
Characteristics subject to change without notice.
4 of 21
REV 1.1.15 5/9/03
www.xicor.com
PIN DESCRIPTIONS
Bus Interface Pins
S
ERIAL
O
UTPUT
(SO)
SO is a serial data output pin. During a read cycle,
data is shifted out on this pin. Data is clocked out by
the falling edge of the serial clock.
S
ERIAL
I
NPUT
(SI)
SI is the serial data input pin. All opcodes, byte
addresses and data to be written to the pots and pot
registers are input on this pin. Data is latched by the
rising edge of the serial clock.
S
ERIAL
C
LOCK
(SCK)
The SCK input is used to clock data into and out of the
X9111.
H
OLD
(HOLD)
HOLD is used in conjunction with the CS pin to select
the device. Once the part is selected and a serial
sequence is underway, HOLD may be used to pause the
serial communication with the controller without resetting
the serial sequence. To pause, HOLD must be brought
LOW while SCK is LOW. To resume communication,
HOLD is brought HIGH, again while SCK is LOW. If the
pause feature is not used, HOLD should be held HIGH at
all times.
D
EVICE
A
DDRESS
(A
0
, A
1
)
The address inputs are used to set the 8-bit slave
address. A match in the slave address serial data
stream must be made with the address input (A1–A0)
in order to initiate communication with the X9111.
C
HIP
S
ELECT
(CS)
When CS is HIGH, the X9111 is deselected and the
SO pin is at high impedance, and (unless an internal
write cycle is underway) the device will be in the
standby state. CS LOW enables the X9111, placing it
in the active power mode. It should be noted that after
a power-up, a HIGH to LOW transition on CS is
required prior to the start of any operation.
H
ARDWARE
W
RITE
P
ROTECT
I
NPUT
(WP)
The WP pin when LOW prevents nonvolatile writes to
the Data Registers.
Potentiometer Pins
R
H
, R
L
The R
connections on a mechanical potentiometer.
H
and R
L
pins are equivalent to the terminal
R
W
The wiper pin is equivalent to the wiper terminal of a
mechanical potentiometer.
Bias Supply Pins
S
YSTEM
S
UPPLY
V
OLTAGE
(V
CC
)
AND
S
UPPLY
G
ROUND
(V
SS
pin
)
The V
is the system ground.
CC
pin is the system supply voltage. The V
SS
Other Pins
N
O
C
ONNECT
(NC)
Pin should be left open. This pin is used for Xicor
manufacturing and test purposes.
PRINCIPLES OF OPERATION
DEVICE DESCRIPTION
Serial Interface
The X9111 supports the SPI interface hardware
conventions. The device is accessed via the SI input
with data clocked-in on the rising SCK. CS must be
LOW and the HOLD and WP pins must be HIGH
during the entire operation.
The SO and SI pins can be connected together, since
they have three state outputs. This can help to reduce
system pin count.
Array Description
The X9111 is comprised of a resistor array (see Figure
1). The array contains the equivalent of 1023 discrete
resistive segments that are connected in series. The
physical ends of each array are equivalent to the fixed
terminals of a mechanical potentiometer (R
inputs).
H
and R
L
At both ends of each array and between each resistor
segment is a CMOS switch connected to the wiper
(R
W
) output. Within the individual array only one switch
may be turned on at a time.
相關PDF資料 |
PDF描述 |
|---|---|
| X9111TV14I-2.7 | Single Digitally-Controlled Potentiometer |
| X9111 | Single Digitally-Controlled Potentiometer |
| X9111TV14 | Single Digitally-Controlled Potentiometer |
| X9111TV14 | Single Supply/Low Power/1024-Tap/SPI Bus |
| X9111TV14-2.7 | Single Supply/Low Power/1024-Tap/SPI Bus |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9111TV14I-2.7 | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9111TV14I-2.7T1 | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9111TV14IZ | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9111TV14IZ-2.7 | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT |
| X9111TV14IZ-2.7T1 | 功能描述:IC POT DGTL 100K OHM 14-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
發(fā)布緊急采購，3分鐘左右您將得到回復。