- 您現在的位置：買賣IC網 > PDF目錄371285 > X9271UB Single Digitally-Controlled (XDCP) Potentiometer PDF資料下載
參數資料
| 型號： | X9271UB |
| 元件分類： | 數字電位計 |
| 英文描述： | Single Digitally-Controlled (XDCP) Potentiometer |
| 中文描述： | 單數字控制（數字電位器）電位 |
| 文件頁數： | 8/23頁 |
| 文件大?。?/td> | 403K |
| 代理商： | X9271UB |
X9271
Characteristics subject to change without notice.
8 of 23
REV 1.1.7 2/6/03
www.xicor.com
Table 5. Instruction Byte Format
I3
I2
I1
P0
RB
RA
P1
P0
(MSB)
(LSB)
Instruction Opcode
Register Selection
Pot Selection (WCR Selection)
Set to P0=0 for potentiometer operations
P1 and P0 are used also for register Bank Selection
for SPI Register Write and Read operations
DEVICE DESCRIPTION
Instructions
Five of the eight instructions are three bytes in length.
These instructions are:
–
Read Wiper Counter Register
– read the current
wiper position of the potentiometer;
–
Write Wiper Counter Register
– change current
wiper position of the potentiometer;
–
Read Data Register
– read the contents of the
selected Data Register;
–
Write Data Register
– write a new value to the
selected Data Register.
–
Read Status
- This command returns the contents of
the WIP bit which indicates if the internal write cycle
is in progress.
The basic sequence of the three byte instructions is
illustrated in Figure 3. These three-byte instructions
exchange data between the WCR and one of the Data
Registers. A transfer from a Data Register to a WCR is
essentially a write to a static RAM, with the static RAM
controlling the wiper position. The response of the
wiper to this action will be delayed by t
WRL
. A transfer
from the WCR (current wiper position), to a Data
Register is a write to nonvolatile memory and takes a
minimum of t
WR
to complete. The transfer can occur
between one of the four potentiometers and one of its
associated registers; or it may occur globally, where
the transfer occurs between all potentiometers and one
associated register. The Read Status Register
instruction is the only unique format (see Figure 4).
Two instructions require a two-byte sequence to
complete (Figure 2). These instructions transfer data
between the host and the X9271; either between the
host and one of the data registers or directly between
the host and the Wiper Counter Register. These
instructions are:
–
XFR Data Register to Wiper Counter Register
–
This transfers the contents of one specified Data
Register to the associated Wiper Counter Register.
–
XFR Wiper Counter Register to Data Register
–
This transfers the contents of the specified Wiper
Counter Register to the specified associated Data
Register.
The final command is Increment/Decrement (Figure 5
and 6). It is different from the other commands,
because it’s length is indeterminate. Once the
command is issued, the master can clock the selected
wiper up and/or down in one resistor segment steps;
thereby, providing a fine tuning capability to the host.
For each SCK clock pulse (t
HIGH
) while SI is HIGH, the
selected wiper will move one resistor segment towards
the R
H
terminal. Similarly, for each SCK clock pulse
while SI is LOW, the selected wiper will move one
resistor segment towards the R
L
terminal.
See Instruction format for more details.
Write in Process (WIP bit)
The contents of the Data Registers are saved to
nonvolatile memory when the CS pin goes from LOW
to HIGH after a complete write sequence is received by
the device. The progress of this internal write operation
can be monitored by a Write In Process bit (WIP). The
WIP bit is read with a Read Status command.
相關PDF資料 |
PDF描述 |
|---|---|
| X9271UB-2.7 | Single Digitally-Controlled (XDCP) Potentiometer |
| X9271UBI | Single Digitally-Controlled (XDCP) Potentiometer |
| X9271UV | Single Digitally-Controlled (XDCP) Potentiometer |
| X9271TXXX | DIGITAL POTENTIOMETER|CMOS|BGA|PLASTIC |
| X9271TXXX-2.7 | DIGITAL POTENTIOMETER|CMOS|BGA|PLASTIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9271UB-2.7 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Single Digitally-Controlled (XDCP) Potentiometer |
| X9271UBI | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Single Digitally-Controlled (XDCP) Potentiometer |
| X9271UBI-2.7 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Single Digitally-Controlled (XDCP) Potentiometer |
| X9271UV | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Single Digitally-Controlled (XDCP) Potentiometer |
| X9271UV14 | 功能描述:IC DIGITAL POT 50K 256TP 14TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。