- 您現在的位置：買賣IC網 > PDF目錄371285 > X9279TB AM29DL800 FLASH MEM 8MB 70NS TSOP-48 PDF資料下載
參數資料
| 型號： | X9279TB |
| 英文描述： | AM29DL800 FLASH MEM 8MB 70NS TSOP-48 |
| 中文描述： | 單數字控制（數字電位器）電位 |
| 文件頁數： | 7/24頁 |
| 文件大?。?/td> | 398K |
| 代理商： | X9279TB |
X9279
Characteristics subject to change without notice.
7 of 24
REV 1.1.7 2/6/03
www.xicor.com
Acknowledge Polling
The disabling of the inputs, during the internal
nonvolatile write operation, can be used to take
advantage of the typical 5ms EEPROM write cycle
time. Once the stop condition is issued to indicate the
end of the nonvolatile write command the X9279
initiates the internal write cycle. ACK polling, Flow 1,
can be initiated immediately. This involves issuing the
start condition followed by the device slave address. If
the X9279 is still busy with the write operation no ACK
will be returned. If the X9279 has completed the write
operation an ACK will be returned and the master can
then proceed with the next operation.
FLOW 1: ACK Polling Sequence
INSTRUCTION AND REGISTER DESCRIPTION
Device Addressing: Identification Byte ( ID and A)
The first byte sent to the X9279 from the host, following
a CS going HIGH to LOW, is called the Identification
byte. The most significant four bits of the slave address
are a device type identifier. The ID[3:0] bits is the
device ID for the X9279; this is fixed as 0101[B] (refer
to Table 1).
The A[2:0] bits in the ID byte is the internal slave
address. The physical device address is defined by the
state of the A2-A0 input pins. The slave address is
externally specified by the user. The X9279 compares
the serial data stream with the address input state; a
successful compare of both address bits is required for
the X9279 to successfully continue the command
sequence. Only the device which slave address
matches the incoming device address sent by the
master executes the instruction. The A2-A0 inputs can
be actively driven by CMOS input signals or tied to V
CC
or V
SS
.
Instruction Byte (I)
The next byte sent to the X9279 contains the
instruction and register pointer information. The three
most significant bits are used provide the instruction
opcode I [2:0]. The RB and RA bits point to one of the
four Data Registers. P0 is the POT selection; since the
X9279 is single POT, the P0=0. The format is shown in
Table 2.
Register Bank Selection (RB, RA, P1, P0)
There are 16 registers organized into four banks. Bank
0 is the default bank of registers. Only Bank 0 registers
can be used for Data Register to Wiper Counter
Register operations.
Banks 1, 2, and 3 are additional banks of registers (12
total) that can be used for 2-Wire write and read
operations. The Data Registers in Banks 1, 2, and 3
cannot be used for direct read/write operations
between the Wiper Counter Register.
Nonvolatile Write
Command Completed
EnterACK Polling
Issue
START
Issue Slave
Address
ACK
Returned
Further
Operation
Issue
Instruction
Issue STOP
No
Yes
Yes
Proceed
Issue STOP
No
Proceed
相關PDF資料 |
PDF描述 |
|---|---|
| X9279TB-2.7 | IC,FLASH 512KX16,BGA DB20 |
| X9279TBI | Single Digitally-Controlled (XDCP) Potentiometer |
| X9279TBI-2.7 | Single Digitally-Controlled (XDCP) Potentiometer |
| X9279TV14 | Single Digitally-Controlled (XDCP) Potentiometer |
| X9279TV14-2.7 | Single Digitally-Controlled (XDCP) Potentiometer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9279TB-2.7 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Single Digitally-Controlled (XDCP) Potentiometer |
| X9279TBI | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Single Digitally-Controlled (XDCP) Potentiometer |
| X9279TBI-2.7 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Single Digitally-Controlled (XDCP) Potentiometer |
| X9279TV14 | 功能描述:IC DGTAL POT 100K 256TP 14TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9279TV14-2.7 | 功能描述:IC DGTAL POT 100K 256TP 14TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。