- 您現在的位置：買賣IC網 > PDF目錄372540 > X9317 Low Noise, Low Power, 100 Taps Digitally-Controlled (XDCPTM) Potentiometer(數控電位器) PDF資料下載
參數資料
| 型號： | X9317 |
| 元件分類： | 數字電位計 |
| 英文描述： | Low Noise, Low Power, 100 Taps Digitally-Controlled (XDCPTM) Potentiometer(數控電位器) |
| 中文描述： | 低噪聲，低功耗，100絲錐數字控制（XDCPTM）電位（數控電位器） |
| 文件頁數： | 3/11頁 |
| 文件大小： | 67K |
| 代理商： | X9317 |
X9317
3
PRINCIPLES OF OPERATION
There are three sections of the X9317: the input control,
counter and decode section; the nonvolatile memory;
and the resistor array. The input control section operates
just like an up/down counter. The output of this counter is
decoded to turn on a single electronic switch connecting
a point on the resistor array to the wiper output. Under
the proper conditions the contents of the counter can be
stored in nonvolatile memory and retained for future use.
The resistor array is comprised of 99 individual resistors
connected in series. At either end of the array and
between each resistor is an electronic switch that
transfers the potential at that point to the wiper.
The wiper, when at either fixed terminal, acts like its
mechanical equivalent and does not move beyond the
last position. That is, the counter does not wrap around
when clocked to either extreme.
The electronic switches on the device operate in a “make
before break” mode when the wiper changes tap
positions. If the wiper is moved several positions, multiple
taps are connected to the wiper for t
change). The R
TOTAL
value for the device can
temporarily be reduced by a significant amount if the
wiper is moved several positions.
IW
(INC to V
W
When the device is powered-down, the last wiper
position stored will be maintained in the nonvolatile
memory. When power is restored, the contents of the
memory are recalled and the wiper is set to the value last
stored.
INSTRUCTIONS AND PROGRAMMING
The INC, U/D and CS inputs control the movement of the
wiper along the resistor array. With CS set LOW, the
device is selected and enabled to respond to the U/D and
INC inputs. HIGH to LOW transitions on INC will
increment or decrement (depending on the state of the
U/D input) a seven bit counter. The output of this counter
is decoded to select one of one hundred wiper positions
along the resistive array.
The value of the counter is stored in nonvolatile memory
whenever CS transistions HIGH while the INC input is
also HIGH.
The system may select the X9317, move the wiper, and
deselect the device without having to store the latest
wiper position in nonvolatile memory. After the wiper
movement is performed as described above and once
the new position is reached, the system must keep INC
LOW while taking CS HIGH. The new wiper will would be
maintained until changed by the system or until a power-
up/down cycle recalled the previously stored data.
This procedure allows the system to always power-up to
a preset value stored in nonvolatile memory; then during
system operation minor adjustments could be made. The
adjustments might be based on user preference, system
parameter changes due to temperature drift, etc...
The state of U/D may be changed while CS remains
LOW. This allows the host system to enable the device
and then move the wiper up and down until the proper
trim is attained.
MODE SELECTION
SYMBOL TABLE
CS
L
L
INC
U/D
H
L
X
X
X
Mode
Wiper Up
Wiper Down
Store Wiper Position
Standby Current
No Store, Return to Standby
H
X
L
H
WAVEFORM
INPUTS
OUTPUTS
Must be
steady
Will be
steady
May change
from Low to
High
May change
from High to
Low
Will change
from Low to
High
Will change
from High to
Low
Don’t Care:
Changes
Allowed
N/A
Changing:
State Not
Known
Center Line
is High
Impedance
相關PDF資料 |
PDF描述 |
|---|---|
| X9318(中文) | Digitally Controlled Potentiometer (XDCP)(單DCP,抽頭位置掉電自動保存,高輸出端電壓,可部分替代X9312W) |
| X9318 | Digitally Controlled Potentiometer (XDCP)(單DCP,抽頭位置掉電自動保存,高輸出端電壓,可部分替代X9312W) |
| x9319(中文) | Digitally Controlled Potentiometer(數字電位器) |
| x9319 | Digitally Controlled Potentiometer(數字電位器) |
| X93256 | Dual Digitally Controlled Potentiometers (XDCPs)(雙數控電位器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9317_09 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Digitally Controlled Potentiometer (XDCP?) |
| X9317TM8 | 功能描述:IC XDCP 100TAP 100K 3WIRE 8-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| X9317TM8-2.7 | 功能描述:IC XDCP 100TAP 100K 3WIRE 8-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| X9317TM8-2.7T1 | 功能描述:IC XDCP 100TAP 100K 3WIRE 8-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| X9317TM8-2.7T2 | 功能描述:IC XDCP 100TAP 100K 3WIRE 8-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。