co" />
參數資料
型號: X93256WV14IZ-2.7
廠商: Intersil
文件頁數: 5/7頁
文件大小: 0K
描述: IC XDCP DUAL 32TAP 12.5K 14TSSOP
產品培訓模塊: Solutions for Industrial Control Applications
標準包裝: 95
系列: XDCP™
接片: 32
電阻(歐姆): 12.5k
電路數: 2
溫度系數: 標準值 ±35 ppm/°C
存儲器類型: 非易失
接口: 6 線串行(芯片選擇,遞增,增/減)
電源電壓: 2.7 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 14-TSSOP(0.173",4.40mm 寬)
供應商設備封裝: 14-TSSOP
包裝: 管件
5
FN8188.2
February 1, 2008
AC Timing
Power-up and Power-down Requirements
There are no restrictions on the power-up or power-down
conditions of VCC and the voltages applied to the
potentiometer pins provided that VCC is always more
positive than or equal to VH and VL, i.e., VCC ≥ VH,VL. The
VCC ramp rate specification is always in effect.
Pin Descriptions
In the text, CS, INC, U/D, RH, RW, and RL are used to refer
to either CS1 or CS2, etc. Note: These signals can be
applied independently or at the same time.
RH and RL
The RH and RL pins of the X93256 are equivalent to the
fixed terminals of a mechanical potentiometer. The minimum
voltage is VSS and the maximum is VCC. The terminology of
RH and RL references the relative position of the terminal in
relation to wiper movement direction selected by the U/D
input per potentiometer.
RW
The RW pin of the X93256 is the wiper terminal of the
potentiometer, which is equivalent to the movable terminal of
a mechanical potentiometer.
Up/Down (U/D)
The U/D input controls the direction of a single
potentiometer’s wiper movement and whether the counter is
incremented or decremented.
Increment (INC)
The INC input is negative-edge triggered. Toggling INC will
move the wiper and either increment or decrement the
pertaining potentiometer’s counter in the direction indicated
by the logic level on the pertaining potentiometer’s U/D
input.
Chip Select (CS)
A potentiometer is selected when the pertaining CS input is
LOW. Its current counter value is stored in nonvolatile memory
when the pertaining CS is returned HIGH while the pertaining
INC input is also HIGH. After the store operation is complete
the affected potentiometer will be placed in the low power
standby mode until the potentiometer is selected once again.
Principles of Operation
There are multiple sections for each potentiometer in the
X93256: an input control, a counter and decode section; the
nonvolatile memory; and a resistor array. Each input control
tlC
INC Inactive to CS Inactive
1
s
tCPH
CS Deselect Time (No store)
250
ns
tCPH
CS Deselect Time (Store)
10
ms
tCYC
INC Cycle Time
2
s
tR, tF
(Note 5)
INC Input Rise and Fall time
500
s
tR VCC
(Note 5)
VCC Power-up Rate
0.2
50
V/ms
tWR
Store Cycle
510
ms
AC Operating Characteristics Over recommended operating conditions, unless otherwise specified. In the table, CS, INC, U/D, RH and
RL are used to refer to either CS1 or CS2, etc. (Continued)
SYMBOL
PARAMETER
MIN
(Note 7)
TYP
(Note 4)
MAX
(Note 7)
UNIT
CS
INC
U/D
tCI
tIL
tIH
tCYC
tID
tDI
tIC
tCPH
tF
tR
10%
90%
(STORE)
Note: CS, INC, U/D, RH and RL are used to refer
to either CS1 or CS2, etc.
X93256
相關PDF資料
PDF描述
VI-25R-MW CONVERTER MOD DC/DC 7.5V 100W
VE-B6B-MY-F1 CONVERTER MOD DC/DC 95V 50W
DS1023S-50 IC DELAY LINE 256TAP 16-SOIC
VE-B64-MY-F4 CONVERTER MOD DC/DC 48V 50W
VI-25P-MX-B1 CONVERTER MOD DC/DC 13.8V 75W
相關代理商/技術參數
參數描述
X93RP-2 功能描述:消費電池與相機電池 C 9185mAh 2 PK Titanium Alkaline RoHS:否 制造商:FDK Batteries 電池大小:CR1/3N 輸出電壓:3 V 容量:160 mAh 化學性質:Lithium 端接類型:Pressure Contacts 可再充電/不可再充電:Non-Rechargeable
X93RP-4 功能描述:消費電池與相機電池 NOT AVAILABLE THROUGH MOUSER RoHS:否 制造商:FDK Batteries 電池大小:CR1/3N 輸出電壓:3 V 容量:160 mAh 化學性質:Lithium 端接類型:Pressure Contacts 可再充電/不可再充電:Non-Rechargeable
X9400 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad Digitally Controlled Potentiometers
X9400_06 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad Digitally Controlled Potentiometers
X94000001-01 功能描述:以太網模塊 XPress-Pro SW 94000 8-Port 10/100TX RoHS:否 制造商:Lantronix 產品:Device Servers 數據速率:300 bps to 921.6 kbps, 10 Mbps, 100 Mbps 接口類型:Ethernet, Serial 工作電源電壓:5 V to 15 V 工作電源電流:133 mA to 400 mA 最大工作溫度:+ 70 C