- 您現在的位置：買賣IC網 > PDF目錄300144 > X9408YB24I-2.7 (INTERSIL CORP) QUAD 2.5K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, BGA24 PDF資料下載
參數資料
| 型號： | X9408YB24I-2.7 |
| 廠商： | INTERSIL CORP |
| 元件分類： | 數字電位計 |
| 英文描述： | QUAD 2.5K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, BGA24 |
| 封裝： | BUMP, CSP-24 |
| 文件頁數： | 4/22頁 |
| 文件大?。?/td> | 395K |
| 代理商： | X9408YB24I-2.7 |
12
FN8191.0
March 3, 2005
D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.)
Notes: (1) Absolute linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used as a
potentiometer.
(2) Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a potentiom-
eter. It is a measure of the error in step size.
(3) MI = RTOT / 63 or [V(VH/RH) – V(VL/RL)] / 63, single pot
ENDURANCE AND DATA RETENTION
CAPACITANCE
POWER-UP TIMING
Power-up Requirements (Power-up sequencing can affect correct recall of the wiper registers)
The preferred power-on sequence is as follows: First V-, then VCC and V+, and then the potentiometer pins, VH/RH,
VL/RL, and VW/RW. Voltage should not be applied to the potentiometer pins before V+ or V- is applied. The VCC
ramp rate specification should be met, and any glitches or slope changes in the VCC line should be held to <100mV if
possible. If VCC powers down, it should be held below 0.1V for more than 1 second before powering up again in order
for proper wiper register recall. Also, VCC should not reverse polarity by more than 0.5V. Recall of wiper position will
not be complete until VCC, V+ and V- reach their final value.
Notes: (4) This parameter is periodically sampled and not 100% tested
(5) tPUR and tPUW are the delays required from the time the third (last) power supply (VCC, V+ or V-) is stable until the specific
instruction can be issued. These parameters are periodically sampled and not 100% tested.
(6) This is not a tested or guaranteed parameter and should only be used as a guidance.
Symbol
Parameter
Limits
Test Conditions
Min.
Typ.
Max.
Unit
ICC1
VCC supply current (nonvolatile
write)
1mA
fSCL = 400kHz, SDA = Open,
Other Inputs = VSS
ICC2
VCC supply current (move wiper,
write, read)
100
A
fSCL = 400kHz, SDA = Open,
Other Inputs = VSS
ISB
VCC current (standby)
1
A
SCL = SDA = VCC, Addr. = VSS
ILI
Input leakage current
10
A
VIN = VSS to VCC
ILO
Output leakage current
10
A
VOUT = VSS to VCC
VIH
Input HIGH voltage
VCC x 0.7
VCC +0.5
V
VIL
Input LOW voltage
–0.5
VCC x 0.1
V
VOL
Output LOW voltage
0.4
V
IOL = 3mA
Parameter
Min.
Unit
Minimum endurance
100,000
Data changes per bit per register
Data retention
100
years
Symbol
Test
Max.
Unit
Test Condition
CI/O
(4)
Input/output capacitance (SDA)
8
pF
VI/O = 0V
CIN
(4)
Input capacitance (A0, A1, A2, A3, and SCL)
6
pF
VIN = 0V
Symbol
Parameter
Min.
Max.
Unit
tPUR
(5)
Power-up to initiation of read operation
1
ms
tPUW
(5)
Power-up to initiation of write operation
5
ms
tRVCC
(6)
VCC Power-up Ramp
0.2
50
V/msec
X9408
相關PDF資料 |
PDF描述 |
|---|---|
| X9409YV24I | QUAD 2.5K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO24 |
| X9417WS24I | DUAL 10K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO24 |
| X9417WS24 | DUAL 10K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO24 |
| X9417YS24-2.7 | DUAL 2.5K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO24 |
| X9418YP24I-2.7 | DUAL 2.5K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDIP24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9408YP24 | 功能描述:IC XDCP QUAD 64-TAP 2.5K 24-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| X9408YP24-2.7 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Digital Potentiometer |
| X9408YP24I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Digital Potentiometer |
| X9408YP24I-2.7 | 功能描述:IC XDCP QUAD 64-TAP 2.5K 24-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| X9408YS24 | 功能描述:IC XDCP QUAD 64-TAP 2.5K 24-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。