- 您現在的位置：買賣IC網 > PDF目錄376448 > X9438WS24-2.7 (INTERSIL CORP) Dual Digitally Controlled Potentiometer (XDCP) with Operational Amplifier PDF資料下載
參數資料
| 型號： | X9438WS24-2.7 |
| 廠商： | INTERSIL CORP |
| 元件分類： | 數字電位計 |
| 英文描述： | Dual Digitally Controlled Potentiometer (XDCP) with Operational Amplifier |
| 中文描述： | DUAL 10K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO24 |
| 封裝： | PLASTIC, SOIC-24 |
| 文件頁數： | 4/18頁 |
| 文件大?。?/td> | 280K |
| 代理商： | X9438WS24-2.7 |
4
FN8199.0
March 11, 2005
The next four bits of the slave address are the device
address. The physical device address is defined by
the state of the A
0
- A
3
inputs. The X9438 compares
the serial data stream with the address input state; a
successful compare of all four address bits is required
for the X9438 to respond with an acknowledge. The
A
0
- A
3
inputs can be actively driven by CMOS input
signals or tied to V
CC
or V
SS
.
Acknowledge Polling
The disabling of the inputs, during the internal non-vol-
atile write operation, can be used to take advantage of
the typical 5ms EEPROM write cycle time. Once the
stop condition is issued to indicate the end of the non-
volatile write command the X9438 initiates the internal
write cycle. ACK polling (Flow 1) can be initiated
immediately. This involves issuing the start condition
followed by the device slave address. If the X9438 is
still busy with the write operation no ACK will be
returned. If the X9438 has completed the write opera-
tion an ACK will be returned and the master can then
proceed with the next operation.
Flow 1. ACK Polling Sequence
Instruction Structure
The byte following the address contains the instruction
and register pointer information. The four most signifi-
cant bits are the instruction. The next four bits point to
one of the two pots and when applicable they point to
one of the four WCRs associated data registers. The
format is shown below in Figure 2.
Figure 2. Instruction Byte Format
The four high order bits define the instruction. The
next two bits (R1 and R0) select one of the two regis-
ters that is to be acted upon when a register oriented
instruction is issued. The last bit (P0) selects which
one of the two potentiometers is to be affected by the
instruction.
Four of the nine instructions end with the transmission
of the instruction byte. The basic sequence is illus-
trated in Figure 3. These two-byte instructions
exchange data between the wiper counter register and
one of the data registers. A transfer from a data regis-
ter to a wiper counter register is essentially a write to a
static RAM. The response of the wiper to this action
will be delayed t
WRL
. A transfer from the wiper counter
register (current wiper position) to a data register is a
write to non-volatile memory and takes a minimum of
t
WR
to complete. The transfer can occur between one
of the two potentiometers and one of its associated
registers; or it may occur globally, wherein the transfer
occurs between all of the potentiometers and one of
their associated registers.
Four instructions require a three-byte sequence to
complete. The basic sequence is illustrated in Figure
4. These instructions transfer data between the host
and the X9438; either between the host and one of the
data registers or directly between the host and the
wiper counter and analog control registers. These
instructions are: 1) Read Wiper Counter Register or
read the current wiper position of the selected pot, 2)
Write Wiper Counter Register, i.e. change current
wiper position of the selected pot; 3) Read Data Regis-
ter, read the contents of the selected non-volatile regis-
ter; 4) Write Data Register, write a new value to the
selected data register. The bit structures of the instruc-
tions are shown in Figure 6.
Nonvolatile Write
Command Completed
Enter Ack Polling
Issue
START
Issue Slave
Address
ACK
Returned
Further
Operation
Issue
Instruction
Issue STOP
No
Yes
Yes
Prooceed
Issue STOP
No
Prooceed
I1
I2
I3
I0
R1
R0
0
P0
WCR Select
Register
Select
Instructions
X9438
相關PDF資料 |
PDF描述 |
|---|---|
| X9438WS24I | Dual Digitally Controlled Potentiometer (XDCP) with Operational Amplifier |
| X9438WS24I-2.7 | Dual Digitally Controlled Potentiometer (XDCP) with Operational Amplifier |
| X9455YV24I-2.7 | Dual Two-wiper Digitally-Controlled (XDCP) Potentiometer |
| X9455 | Dual Two-wiper Digitally-Controlled (XDCP) Potentiometer |
| X9455TV24-2.7 | Dual Two-wiper Digitally-Controlled (XDCP) Potentiometer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9438WS24I | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual Digitally Controlled Potentiometer (XDCP) with Operational Amplifier |
| X9438WS24I-2.7 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual Digitally Controlled Potentiometer (XDCP) with Operational Amplifier |
| X9438WV24 | 功能描述:IC DUAL DCP + OPAMP 10K 24TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:3,300 系列:WiperLock™ 接片:257 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 150 ppm/°C 存儲器類型:易失 接口:3 線 SPI（芯片選擇） 電源電壓:1.8 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-VDFN 裸露焊盤 供應商設備封裝:8-DFN-EP（3x3） 包裝:帶卷 (TR) |
| X9438WV24-2.7 | 功能描述:IC DUAL DCP + OPAMP 10K 24TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT |
| X9438WV24I | 功能描述:IC DUAL DCP + OPAMP 10K 24TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT |
發布緊急采購，3分鐘左右您將得到回復。