- 您現在的位置：買賣IC網 > PDF目錄9415 > X9440WS24 (Intersil)IC DUAL PROG COMP 10K 64TP SO24 PDF資料下載
參數資料
| 型號： | X9440WS24 |
| 廠商： | Intersil |
| 文件頁數： | 12/21頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DUAL PROG COMP 10K 64TP SO24 |
| 標準包裝： | 30 |
| 系列： | XDCP™ |
| 接片： | 64 |
| 電阻（歐姆）： | 10k |
| 電路數： | 2 |
| 溫度系數： | 標準值 ±300 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | 6 線 SPI（芯片選擇，設備位址） |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 24-SOIC |
| 包裝： | 管件 |
2
FN8200.0
March 28, 2005
PIN DESCRIPTIONS
Host Interface Pins
Serial Output (SO)
SO is a push/pull serial data output pin. During a read
cycle, data is shifted out on this pin. Data is clocked
out by the falling edge of the serial clock.
Serial Input (SI)
SI is the serial data input pin. All opcodes, byte
addresses and data to be written to the pots and pot
registers are input on this pin. Data is latched by the
rising edge of the serial clock.
Serial Clock (SCK)
The SCK input is used to clock data into and out of the
X9440.
Chip Select (CS)
When CS is HIGH, the X9440 is deselected and the
SO pin is at high impedance, and (unless an internal
write cycle is underway) the device will be in the
standby state. CS LOW enables the X9440, placing it
in the active power mode. It should be noted that after
a power-up, a HIGH to LOW transition on CS is
required prior to the start of any operation.
Hold (HOLD)
HOLD is used in conjunction with the CS pin to select
the device. Once the part is selected and a serial
sequence is underway, HOLD may be used to pause
the serial communication with the controller without
resetting the serial sequence. To pause, HOLD must
be brought LOW while SCK is LOW. To resume com-
munication, HOLD is brought HIGH, again while SCK
is LOW. If the pause feature is not used, HOLD should
be held HIGH at all times.
Device Address (A0-A1)
The address inputs are used to set the least significant
2 bits of the 8-bit slave address. A match in the slave
address serial data stream must be made with the
Address input in order to initiate communication with
the X9440. A maximum of 4 devices may share the
same SPI serial bus.
Potentiometer Pins
VH (VH0-VH3), VL (VL0-VL3)
The VH and VL inputs are equivalent to the terminal con-
nections on either end of a mechanical potentiometer.
VW (VW0-VW1)
The wiper output VW is equivalent to the wiper output
of a mechanical potentiometer and is connected to the
inverting input of the voltage comparator.
Comparator and Device Pins
Voltage Input VNI0, VNI1
VNI0 and VNI1 are the input voltages to the plus (non-
inverting) inputs of the two comparators.
Buffered Voltage Outputs VOUT0, VOUT1
VOUT0 and VOUT1 are the buffered voltage comparator
outputs controlled by bits in the volatile analog control
register.
Hardware Write Protect Input WP
The WP pin when low prevents non volatile writes to
the wiper counter and analog control registers.
Analog Supplies V+, V-
The Analog Supplies V+, V- are the supply voltages for
the XDCP analog section and the voltage comparators.
System Supply VCC and Ground VSS
The system supply, VCC and its reference VSS is used
to bias the interface and control circuits.
X9440
相關PDF資料 |
PDF描述 |
|---|---|
| X9448WS24-2.7 | IC DUAL PROG COMP 10K 64TP SO24 |
| CDP68HC68T1M2 | IC RTC 32X8 NVSRAM CMOS 16-SOIC |
| X9448WS24 | IC DUAL PROG COMP 10K 64TP SO24 |
| X9438WV24-2.7 | IC DUAL DCP + OPAMP 10K 24TSSOP |
| VI-221-MY-F2 | CONVERTER MOD DC/DC 12V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9440WS24-2.7 | 功能描述:IC DUAL PROG COMP 10K 64TP SO24 RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT |
| X9440WS24I | 功能描述:IC DUAL PROG COMP 10K 64TP SO24 RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT |
| X9440WS24I-2.7 | 功能描述:IC DUAL PROG COMP 10K 64TP SO24 RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT |
| X9440WS24I27 | 制造商:Intersil Corporation 功能描述: 制造商:XICOR 功能描述: |
| X9440WV24 | 功能描述:IC DUAL PROG COMP 10K 24TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT |
發布緊急采購，3分鐘左右您將得到回復。