- 您現在的位置：買賣IC網 > PDF目錄376448 > X9460KV14I (INTERSIL CORP) Dual Audio Control Digitally Controlled Potentiometer PDF資料下載
參數資料
| 型號： | X9460KV14I |
| 廠商： | INTERSIL CORP |
| 元件分類： | 數字電位計 |
| 英文描述： | Dual Audio Control Digitally Controlled Potentiometer |
| 中文描述： | DUAL 33K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 32 POSITIONS, PDSO14 |
| 封裝： | PLASTIC, TSSOP-14 |
| 文件頁數： | 4/16頁 |
| 文件大?。?/td> | 308K |
| 代理商： | X9460KV14I |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
4
FN8203.2
October 17, 2005
Detailed Pin Description
Host Interface Pins
SERIAL CLOCK (SCL)
The SCL input clocks data into and out of the X9460.
SERIAL DATA (SDA)
SDA is a bidirectional pin used to transfer data into and out
of the device. It is an open drain output and may be wire-
ORed with any number of open drain or open collector
outputs. An open drain output requires the use of a pull-up
resistor. For selecting typical values, refer to the guidelines
for calculating typical values on the bus pull-up resistors
graph.
DEVICE ADDRESS (A
1
- A
0
)
The Address inputs are used to set the least significant 2 bits
of the 8-bit Slave Byte Address. A match in the slave
address serial data stream must be made with the Address
input in order to initiate communication with the X9460. Up to
4 X9460s may be connected to a single I
2
C serial bus and
written to (NOTE: you cannot read from more than one
device on the same 2-wire bus). If left floating, these pins are
internally pulled to ground.
Slave Byte (bits, MSB-LSB) = 0101 0 A
1
A
0
R/W
Potentiometer Pins
R
H-LEFT
, R
L-LEFT
, R
H-RIGHT
, R
L-RIGHT
The R
H
and R
L
inputs are equivalent to the terminal
connections on either end of a mechanical potentiometer.
R
W-LEFT
, R
W-RIGHT
The wiper outputs are equivalent to the wiper output of a
mechanical potentiometer.
Supply Pins
ANALOG SUPPLY V- AND V+
The positive power supply for the DCP analog control
section is connected to V+. The negative power supply for
the DCP analog control section is connected to V-.
DIGITAL SUPPLIES V
CC
, V
SS
The power supplies for the digital control sections.
Power-up and Down Recommendations
There are no restrictions on the power-up condition of V
CC
,
V+ and V- and the voltages applied to the potentiometer pins
provided that the V
CC
and V+ are more positive or equal to
the voltage at R
H
, R
L
, and R
W
, ie. V
CC
, V+ > R
H
, R
L
, R
W
. At
all times, the voltages on the potentiometer pins must be
less than V+ and more than V-.
The following V
CC
ramp rate spec is always in effect.
0.2 V/ms < V
CC
ramp < 50 V/ms
The V
SS
pin is always connected to the system common or
ground. V
H
, V
L
, V
W
are the voltages on the R
H
, R
L
, and R
W
potentiometer pins.
X9460 Principles of Operation
The X9460 is a highly integrated microcircuit incorporating
two resistor arrays with their associated registers, counters
and the serial interface logic providing direct communication
between the host and the DCP potentiometers. This section
provides detailed description as following:
- Resistor Array Description
- Serial Interface Description
- Command Set and Register Information Description
Resistor Array Description
The X9460 is comprised of two resistor arrays. Each array
contains 31 discrete resistive segments that are connected
in series. The physical ends of each array are equivalent to
the fixed terminals of a mechanical potentiometer (R
H
and
R
L
inputs). Tables 1 and 2 provide a description of the step
size and tap positions.
At both ends of each array and between each resistor
segment is a CMOS switch connected to the wiper (R
W
)
output. Within each individual array only one switch may be
turned on at a time. These switches are controlled by the
Wiper Counter Register (WCR). The five bits of the WCR are
decoded to select, and enable, one of thirty-two switches.
TABLE 1. TOTAL -62dB RANGE PLUS MUTE POSITION
STEP SIZE
# OF STEPS
-1dB
11 steps
- 2dB
10 steps
- 3dB
5 steps
- 4dB
4 steps
Mute
1 step
TABLE 2. WIPER TAP POSITION vs dB
TAP POSITION, n
dB
MIN/MAX dB
for n = 20 to 31
n - 31
-11/0
for n = 10 to 19
2n-51
-31/-13
for n = 5 to 9
3n-61
-46/-34
for n = 1 to 4
4n-66
-62/-50
n = 0
-92
-92
X9460
相關PDF資料 |
PDF描述 |
|---|---|
| X9460KV14I-2.7 | Dual Audio Control Digitally Controlled Potentiometer |
| X9460KV14IZ | Dual Audio Control Digitally Controlled Potentiometer |
| X9460KV14IZ-2.7 | Dual Audio Control Digitally Controlled Potentiometer |
| X9460 | Dual Audio Control Digitally Controlled Potentiometer |
| X9520B20IA | Triple DCP, POR,2kbit EEPROM Memory, Dual Voltage Monitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9460KV14I-2.7 | 功能描述:IC XDCP DUAL AUD 32T 33K 14TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| X9460KV14I-2.7T1 | 功能描述:IC XDCP DUAL AUD 32T 33K 14TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| X9460KV14IT1 | 功能描述:IC XDCP DUAL AUD 32T 33K 14TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| X9460KV14IZ | 功能描述:IC XDCP DUAL AUD 32T 33K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9460KV14IZ-2.7 | 功能描述:IC XDCP DUAL AUD 32T 33K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。