- 您現在的位置：買賣IC網 > PDF目錄376449 > X9522B20I-A (INTERSIL CORP) Laser Diode Control for Fiber Optic Modules PDF資料下載
參數資料
| 型號： | X9522B20I-A |
| 廠商： | INTERSIL CORP |
| 元件分類： | 數字電位計 |
| 英文描述： | Laser Diode Control for Fiber Optic Modules |
| 中文描述： | DIGITAL POTENTIOMETER, PBGA20 |
| 封裝： | BGA-20 |
| 文件頁數： | 14/29頁 |
| 文件大小： | 486K |
| 代理商： | X9522B20I-A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
14
FN8208.0
March 10, 2005
Setting a Higher V
TRIPx
Voltage (x = 2,3)
To set a V
TRIPx
threshold to a new voltage which is
higher than the present threshold, the user must apply
the desired V
TRIPx
threshold voltage to the corre-
sponding input pin (V2 or V3). Then, a programming
voltage (Vp) must be applied to the WP pin before a
START condition is set up on SDA. Next, issue on the
SDA pin the Slave Address A0h, followed by the Byte
Address 09h for V
TRIP3
, and 0Dh for V
TRIP3
, and a 00h
Data Byte in order to program V
TRIPx
. The STOP bit
following a valid write operation initiates the program-
ming sequence. Pin WP must then be brought LOW to
complete the operation (See Figure 16). The user
does not have to set the WEL bit in the CONSTAT reg-
ister before performing this write sequence.
Setting a Lower V
TRIPx
Voltage (x = 2,3)
In order to set V
TRIPx
to a lower voltage than the
present value, then V
TRIPx
must first be “reset” accord-
ing to the procedure described below. Once V
TRIPx
has been “reset”, then V
TRIPx
can be set to the desired
voltage using the procedure described in “Setting a
Higher V
TRIPx
Voltage”.
Resetting the V
TRIPx
Voltage
To reset a V
TRIPx
voltage, apply the programming volt-
age (Vp) to the WP pin before a START condition is set
up on SDA. Next, issue on the SDA pin the Slave
Address A0h followed by the Byte Address 0Bh for
V
TRIP2
, and 0Fh for V
TRIP3
, followed by 00h for the
Data Byte in order to reset V
TRIPx
. The STOP bit fol-
lowing a valid write operation initiates the program-
ming sequence. Pin WP must then be brought LOW to
complete the operation (See Figure 16).The user does
not have to set the WEL bit in the CONSTAT register
before performing this write sequence.
After being reset, the value of V
TRIPx
becomes a nomi-
nal value of 1.7V.
V
TRIPx
Accuracy (x = 2,3)
The accuracy with which the V
TRIPx
thresholds are set,
can be controlled using the iterative process shown in
Figure 17.
If the desired threshold is less that the present threshold
voltage, then it must first be “reset” (See "Resetting the
VTRIPx Voltage").
The desired threshold voltage is then applied to the
appropriate input pin (V2 or V3) and the procedure
described in Section “Setting a Higher V
TRIPx
Voltage“
must be followed.
Once the desired V
TRIPx
threshold has been set, the
error between the desired and (new) actual set threshold
can be determined. This is achieved by applying Vcc / V1
to the device, and then applying a test voltage higher
than the desired threshold voltage, to the input pin of the
voltage monitor circuit whose V
TRIPx
was programmed.
For example, if V
TRIP2
was set to a desired level of 3.0 V,
then a test voltage of 3.4 V may be applied to the voltage
monitor input pin V2. In all cases, care should be taken
not to exceed the maximum input voltage limits.
After applying the test voltage to the voltage monitor
input pin, the test voltage can be decreased (either in dis-
crete steps, or continuously) until the output of the volt-
age monitor circuit changes state. At this point, the error
between the actual / measured, and desired threshold
levels is calculated.
For example, the desired threshold for V
TRIP2
is set to
3.0 V, and a test voltage of 3.4 V was applied to the input
pin V2 (after applying power to Vcc / V1). The input volt-
age is decreased, and found to trip the associated output
level of pin V2RO from a LOW to a HIGH, when V2
reaches 3.09 V. From this, it can be calculated that the
programming error is 3.09 - 3.0 = 0.09 V.
If the error between the desired and measured V
TRIPx
is
less than the maximum desired error, then the program-
ming process may be terminated. If however, the error is
greater than the maximum desired error, then another
iteration of the V
TRIPx
programming sequence can be
performed (using the calculated error) in order to further
increase the accuracy of the threshold voltage.
If the calculated error is greater than zero, then the
V
TRIPx
must first be “reset”, and then programmed to the
a value equal to the previously set V
TRIPx
minus the cal-
culated error. If it is the case that the error is less than
zero, then the V
TRIPx
must be programmed to a value
equal to the previously set V
TRIPx
plus the absolute value
of the calculated error.
Continuing the previous example, we see that the calcu-
lated error was 0.09V. Since this is greater than zero, we
must first “reset” the V
TRIP2
threshold, then apply a volt-
age equal to the last previously programmed voltage,
minus the last previously calculated error. Therefore, we
must apply V
TRIP1
= 2.91 V to pin V2 and execute the
programming sequence (See "Setting a Higher VTRIPx
Voltage (x = 2,3)" ) .
Using this process, the desired accuracy for a particu-
lar V
TRIPx
threshold may be attained using a succes-
sive number of iterations.
X9522
相關PDF資料 |
PDF描述 |
|---|---|
| X9522B20I-B | Laser Diode Control for Fiber Optic Modules |
| X9522V20I-A | Laser Diode Control for Fiber Optic Modules |
| X9522V20I-B | Laser Diode Control for Fiber Optic Modules |
| X9523V20I-A | Laser Diode Control for Fiber Optic Modules |
| X9523V20I-B | Laser Diode Control for Fiber Optic Modules |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9522B20I-B | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Laser Diode Control for Fiber Optic Modules |
| X9522V20I-A | 功能描述:IC TRIPL DCP LASER CNTRL 20TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9522V20I-AT1 | 功能描述:IC DCP DUAL EEPROM MEM 20-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9522V20I-B | 功能描述:IC TRIPL DCP LASER CNTRL 20TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9522V20I-BT1 | 功能描述:IC DCP DUAL EEPROM MEM 20-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
發布緊急采購，3分鐘左右您將得到回復。