- 您現在的位置：買賣IC網 > PDF目錄19901 > XC17V04VQ44I (Xilinx Inc)IC PROM SER 4MBIT 3.3V 44-VQFP PDF資料下載
參數資料
| 型號： | XC17V04VQ44I |
| 廠商： | Xilinx Inc |
| 文件頁數： | 13/15頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PROM SER 4MBIT 3.3V 44-VQFP |
| 標準包裝： | 160 |
| 可編程類型： | OTP |
| 存儲容量： | 4Mb |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 44-TQFP |
| 供應商設備封裝： | 44-VQFP（10x10） |
| 包裝： | 托盤 |
XC17V00 Series Configuration PROMs
DS073 (v2.0) April 7, 2014
Product Specification
7
R
— OBSOLETE — OBSOLETE — OBSOLETE — OBSOLETE — OBSOLETE —
Controlling PROMs
Connecting the FPGA device with the PROM.
The DATA output(s) of the PROM(s) drives the
configuration data input(s) of the lead FPGA device.
The Master FPGA CCLK output drives the CLK input(s)
of the PROM(s).
The CEO output of a PROM drives the CE input of the
next PROM in a daisy chain (if any).
The RESET/OE input of all PROMs is best driven by
the INIT output of the lead FPGA device. This
connection assures that the PROM address counter is
reset before the start of any (re)configuration, even
when a reconfiguration is initiated by a VCC glitch.
The PROM CE input is best connected to the FPGA
DONE pin(s) and a pullup resistor. CE can also be
permanently tied Low, but this keeps the DATA output
active and causes an unnecessary supply current of
15 mA maximum.
SelectMAP mode is similar to Slave Serial mode. The
DATA is clocked out of the PROM one byte per CCLK
instead of one bit per CCLK cycle. See FPGA data
sheets for special configuration requirements.
FPGA Master Serial Mode Summary
The I/O and logic functions of the Configurable Logic Block
(CLB) and their associated interconnections are established
by a configuration program. The program is loaded either
automatically upon power up, or on command, depending
on the state of the three FPGA mode pins. In Master Serial
mode, the FPGA automatically loads the configuration
program from an external memory. The Xilinx PROMs have
been designed for compatibility with the Master Serial
mode.
Upon power-up or reconfiguration, an FPGA enters the
Master Serial mode whenever all three of the FPGA mode-
select pins are Low (M0=0, M1=0, M2=0). Data is read from
the PROM sequentially on a single data line.
Synchronization is provided by the rising edge of the
temporary signal CCLK, which is generated during
configuration.
Master Serial Mode provides a simple configuration
interface. Only one serial data line, two control lines, and
one clock line are required to configure an FPGA. Data from
the PROM is read sequentially, accessed via the internal
address and bit counters which are incremented on every
valid rising edge of CCLK.
If the user-programmable, dual-function DIN pin on the
FPGA is used only for configuration, it must still be held at a
defined level during normal operation. The Xilinx FPGA
families take care of this automatically with an on-chip
default pull-up/down resistor or keeper circuit.
Cascading Configuration PROMs
For multiple FPGAs configured as a daisy-chain, or for
future FPGAs requiring larger configuration memories,
cascaded PROMs provide additional memory. After the last
bit from the first PROM is read, the next clock signal to the
PROM asserts its CEO output Low and disables its DATA
line. The second PROM recognizes the Low level on its CE
input and enables its DATA output. See Figure 3.
After configuration is complete, the address counters of all
cascaded PROMs are reset if the FPGA PROGRAM pin
goes Low, assuming the PROM reset polarity option has
been inverted.
Standby Mode
The PROM enters a low-power standby mode whenever CE
is asserted High. The output remains in a high impedance
state regardless of the state of the OE input.
Programming
The devices can be programmed on programmers supplied
by Xilinx or qualified third-party vendors. The user must
ensure that the appropriate programming algorithm and the
latest version of the programmer software are used. The
wrong choice can permanently damage the device.
Selecting Reset Polarity and
Configuration Modes
The OE/RESET input polarity is programmable on all
XC17V00 PROMs. In addition, the XC17V08 and XC17V16
can accommodate either serial or parallel configuration
mode. The reset polarity and configuration mode are
selectable through the programmer software. For
compatibility with Xilinx FPGAs, the OE/RESET polarity
must be programmed with RESET active-Low.
相關PDF資料 |
PDF描述 |
|---|---|
| LNK603DG | IC OFFLINE SWIT CV/CC HV 8SOIC |
| XC17V16PC44C | IC PROM SER C-TEMP 3.3V 44-PLCC |
| GRM21BR72A223KA01L | CAP CER 0.022UF 100V X7R 0805 |
| R-78AA5.0-0.5SMD-R | CONV DC/DC 0.5A 5V OUT SMD |
| ASM22DTMH | CONN EDGECARD 44POS R/A .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XC17V04VQG44C | 制造商:Xilinx 功能描述:PROM PARALLEL/SERIAL 4M-BIT 3.3V 44-PIN VTQFP - Rail/Tube |
| XC17V08PC20C | 制造商:XILINX 制造商全稱:XILINX 功能描述:XC17V00 Series Configuration PROM |
| XC17V08PC20I | 制造商:XILINX 制造商全稱:XILINX 功能描述:XC17V00 Series Configuration PROM |
| XC17V08PC44C | 功能描述:IC PROM SER C-TEMP 3.3V 44-PLCC RoHS:否 類別:集成電路 (IC) >> 存儲器 - 用于 FPGA 的配置 Proms 系列:- 產品變化通告:Product Discontinuation 28/Jul/2010 標準包裝:98 系列:- 可編程類型:OTP 存儲容量:300kb 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-TSOP 包裝:管件 |
| XC17V08PC44I | 功能描述:IC PROM SER I-TEMP 3.3V 44-PLCC RoHS:否 類別:集成電路 (IC) >> 存儲器 - 用于 FPGA 的配置 Proms 系列:- 產品變化通告:Product Discontinuation 28/Jul/2010 標準包裝:98 系列:- 可編程類型:OTP 存儲容量:300kb 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-TSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。