- 您現在的位置：買賣IC網 > PDF目錄19901 > XC17V16VQ44C (Xilinx Inc)IC PROM SER C-TEMP 3.3V 44-VQFP PDF資料下載
參數資料
| 型號： | XC17V16VQ44C |
| 廠商： | Xilinx Inc |
| 文件頁數： | 9/15頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PROM SER C-TEMP 3.3V 44-VQFP |
| 標準包裝： | 160 |
| 可編程類型： | OTP |
| 存儲容量： | 16Mb |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | 0°C ~ 70°C |
| 封裝/外殼： | 44-TQFP |
| 供應商設備封裝： | 44-VQFP（10x10） |
| 包裝： | 托盤 |
XC17V00 Series Configuration PROMs
DS073 (v2.0) April 7, 2014
Product Specification
3
R
— OBSOLETE — OBSOLETE — OBSOLETE — OBSOLETE — OBSOLETE —
Pin Description
DATA[0:7]
The array data value corresponding to the internal address
counter location is output on enabled DATA[0-7] output
pin(s) when CE is active, OE is active, and the internal
address counter has not incremented beyond its Terminal
Count (TC) value. Otherwise, all data pins are in a high
impedance state when CE is inactive, OE is inactive, or the
internal address counter has incremented beyond its
Terminal Count (TC) value.
The XC17V01, XC17V02, and XC17V04 have only the
single DATA output pin for connection to the FPGA serial
configuration data input pin.
The XC17V08 and XC17V16 have the D[0-7] output pins.
During device programming, the XC17V08 and XC17V16
must be programmed for use in either serial output mode or
parallel output mode. For XC17V08 and XC17V16 devices
programmed to serial output mode, only the D0 pin is
enabled for data output to the Virtex series FPGA serial
configuration data input pin. In serial mode, the D[1-7]
output pins remain in high impedance state and may be
unconnected. For XC17V08 and XC17V16 devices
programmed to parallel output mode, all D[0-7] output pins
are enabled for byte-wide data output to the FPGA
SelectMAP configuration data input pins.
The DATA/D0 pin is a bidirectional I/O during device
programming.
CLK
Each rising edge on the CLK input increments the internal
address counter, when CE is active, OE is active, the
internal address counter has not incremented past its
Terminal Count (TC) value, and BUSY is Low.
Note: The BUSY condition applies to only the XC17V08 and
XC17V16.
RESET/OE
The polarity of this input pin is programmable as either
RESET/OE or OE/RESET. The polarity is set at the time of
device programming. The device default is active-High
RESET, but compatibility with Xilinx FPGAs requires the
polarity to be programmed with an active-Low RESET.
When RESET is active, the address counter is held at “0”,
and puts the DATA output in a high-impedance state.
CE
When High, this pin holds the internal address counter in
reset, puts the DATA output in a high-impedance state, and
forces the device into low-ICC standby mode.
CEO
Chip Enable Output is connected to the CE input of the next
PROM in the daisy chain. This output is Low when the CE
and OE inputs are both active AND the internal address
counter has been incremented beyond its Terminal Count
(TC) value. CEO returns to High when OE goes inactive or
CE goes High.
BUSY (XC17V16 and XC17V08 Only)
Asserting the BUSY input High prevents rising edges on
CLK from incrementing the internal address counter and
maintains current data on the data pins.
Note: If the BUSY pin is floating, then the programmable option
to internally tie BUSY to an internal pull-down resistor must be set
during device programming.
VPP
Programming voltage. No overshoot above the specified
maximum voltage is permitted on this pin. For normal read
operation, this pin must be connected to VCC. Failure to do
so may lead to unpredictable, temperature-dependent
operation and severe problems in circuit debugging.
Caution! Do not leave VPP floating!
VCC and GND
Positive supply and ground pins.
PROM Pinouts for XC17V16 and XC17V08
Pins not listed in Table 1 are “no connect.”
Table 1: Pinouts for XC17V16 and XC17V08(1)
Pin Name
44-pin VQFP (VQ44)
44-pin PLCC (PC44)
BUSY
24
30
D0
40
2
D1
29
35
D2
42
4
D3
27
33
D4
9
15
D5
25
31
D6
14
20
D7
19
25
CLK
43
5
RESET/OE
(OE/RESET)
13
19
CE
15
21
GND
6, 18, 28, 37, 41
3, 12, 24, 34, 43
CEO
21
27
相關PDF資料 |
PDF描述 |
|---|---|
| 395-050-558-201 | CONN CARDEDGE 50POS .100X.200 |
| GSM06DRYH | CONN EDGECARD 12POS DIP .156 SLD |
| XC18V04PC44C | IC PROM SER C-TEMP 3.3V 44-PLCC |
| AGM22DTMH | CONN EDGECARD 44POS R/A .156 SLD |
| XC17V04PC44I | IC PROM SER 4MBIT 3.3V 44-PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XC17V16VQ44I | 功能描述:IC PROM SER I-TEMP 3.3V 44-VQFP RoHS:否 類別:集成電路 (IC) >> 存儲器 - 用于 FPGA 的配置 Proms 系列:- 產品變化通告:Product Discontinuation 28/Jul/2010 標準包裝:98 系列:- 可編程類型:OTP 存儲容量:300kb 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-TSOP 包裝:管件 |
| XC1800 | 制造商:XILINX 制造商全稱:XILINX 功能描述:XC1800 Series of In-System Programmable Configuration PROMs |
| XC1804VQ44C | 制造商:Xilinx 功能描述:Serial EEPROM, 44 Pin, Plastic, TQFP |
| XC1804VQ44C-ES | 制造商:Xilinx 功能描述:Serial EEPROM, 44 Pin, Plastic, TQFP |
| XC18V00 | 制造商:XILINX 制造商全稱:XILINX 功能描述:In-System Programmable Configuration PROMs |
發布緊急采購，3分鐘左右您將得到回復。