- 您現在的位置：買賣IC網 > PDF目錄19827 > XC2C256-7CPG132C (Xilinx Inc)IC CR-II CPLD 256MCELL 132-BGA PDF資料下載
參數資料
| 型號： | XC2C256-7CPG132C |
| 廠商： | Xilinx Inc |
| 文件頁數： | 5/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CR-II CPLD 256MCELL 132-BGA |
| 標準包裝： | 360 |
| 系列： | CoolRunner II |
| 可編程類型： | 系統內可編程 |
| 最大延遲時間 tpd(1)： | 6.7ns |
| 電壓電源 - 內部： | 1.7 V ~ 1.9 V |
| 邏輯元件/邏輯塊數目： | 16 |
| 宏單元數： | 256 |
| 門數： | 6000 |
| 輸入/輸出數： | 106 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 132-TFBGA，CSPBGA |
| 供應商設備封裝： | 132-CSPBGA（8x8） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 600 (CN2011-ZH PDF) |
| 配用： | 122-1573-ND - KIT STARTER COOLRUNNER-II LP/LC 122-1512-ND - KIT DESIGN CPLD W/BATT HOLDER |
| 其它名稱： | 122-1399 |
CoolRunner-II CPLD Family
DS090 (v3.1) September 11, 2008
13
Product Specification
R
to be programmed at any time. All devices are shipped in
the erased state from the factory.
Applying power to a blank part might result in a higher cur-
rent flow as the part initializes. This behavior is normal and
might persist for approximately 2 seconds, depending on
the power supply ramp.
If the device is programmed, the device inputs and outputs
take on their configured states for normal operation. The
JTAG pins are enabled to allow device erasure or bound-
ary-scan tests at any time.
I/O Banking
CoolRunner-II CPLD XC2C32A and XC2C64A macrocell
parts support two VCCIO rails that can range from 3.3V
down to 1.5V operation. Two VCCIO rails are supported on
the 128 and 256 macrocell parts where outputs on each rail
can independently range from 3.3V down to 1.5V operation.
Four VCCIO rails are supported on the 384 and 512 macro-
cell parts. Any of the VCCIO rails can assume any one of the
VCCIO values of 1.5V, 1.8V, 2.5V, or 3.3V. Designers should
assign input and output voltages to a bank with VCCIO set at
the voltage range of that input or output voltage. The VCC
(internal supply voltage) for a CoolRunner-II CPLD must be
maintained within 1.8V ±5% for correct speed operation and
proper in system programming.
Mixed Voltage, Power Sequencing, and
Hot Plugging
As mentioned in I/O Banking, CoolRunner-II CPLD parts
support mixed voltage I/O signals. It is important to assign
signals to an I/O bank with the appropriate I/O voltage. Driv-
ing a high voltage into a low voltage bank can result in neg-
ative current flow through the power supply pins. The power
applied to the VCCIO and VCC pins can occur in any order
and the CoolRunner-II CPLD will not be damaged. For best
results, Xilinx recommends that VCCINT be applied before
VCCIO To ensure that the internal logic is correct before the
I/Os are active. CoolRunner-II CPLDs can reside on boards
where the board is inserted into a “l(fā)ive” connector (hot
plugged) and the parts will be well-behaved as if powering
up in a standard way.
Development System Support
Xilinx CoolRunner-II CPLDs are supported by all configura-
tions of Xilinx standard release development software as
well as the freely available ISE WebPACK software avail-
able from www.xilinx.com. Third party development tools
include synthesis tools from Cadence, Exemplar, Mentor
Graphics, Synplicity, and Synopsys.
ATE Support
Third party ATE development support is available for both
programming and board/chip level testing. Vendors provid-
ing this support include Agilent, GenRad, and Teradyne.
Other third party providers are expected to deliver solutions
in the future.
Figure 12: Device Behavior During Power Up
VCCINT
No
Power
3.8 V
(Typ)
0V
No
Power
Quiescent
State
Quiescent
State
User Operation
Initialization Transition of User Array
x382_10
1.3V
(Typ)
Table 8: I/O Power-Up Characteristics
Device Circuitry
Quiescent State
Erased Device Operation
Valid User Operation
IOB Bus-Hold/Weak Pullup
Weak Pull-up
Bus-Hold/Weak Pullup
Device Outputs
Disabled
As Configured
Device Inputs and Clocks
Disabled
As Configured
Function Block
Disabled
As Configured
JTAG Controller
Disabled
Enabled
相關PDF資料 |
PDF描述 |
|---|---|
| RSO-1212S/H2 | CONV DC/DC 1W 9-18VIN 12VOUT |
| VI-BWW-CY-F4 | CONVERTER MOD DC/DC 5.5V 50W |
| RSO-1209S/H2 | CONV DC/DC 1W 9-18VIN 09VOUT |
| XC95144XL-5TQG144C | IC CPLD 3.2K 144MCELL 144-TQFP |
| VE-24W-EV-F1 | CONVERTER MOD DC/DC 5.5V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XC2C256-7CPG132I | 功能描述:IC CR-II CPLD 256MCELL 132CSBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - CPLD（復雜可編程邏輯器件） 系列:CoolRunner II 標準包裝:24 系列:CoolRunner II 可編程類型:系統內可編程 最大延遲時間 tpd(1):7.1ns 電壓電源 - 內部:1.7 V ~ 1.9 V 邏輯元件/邏輯塊數目:24 宏單元數:384 門數:9000 輸入/輸出數:173 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:208-BFQFP 供應商設備封裝:208-PQFP（28x28） 包裝:托盤 |
| XC2C256-7FT256C | 制造商:Xilinx 功能描述:CPLD COOLRUNNER-II 6K GATES 256 MCRCLLS 300MHZ 0.18UM 1.8V 2 - Trays 制造商:Xilinx 功能描述:IC SYSTEM GATE 制造商:Xilinx 功能描述:IC CR-II CPLD 256MCELL 256-BGA |
| XC2C2567FT256I | 制造商:XILINX 功能描述:New |
| XC2C256-7FT256I | 制造商:Xilinx 功能描述:CPLD COOLRUNNER-II 6K GATES 256 MCRCLLS 300MHZ 0.18UM 1.8V 2 - Trays 制造商:Xilinx 功能描述:IC SYSTEM GATE 制造商:Xilinx 功能描述:IC CR-II CPLD 256MCELL 256-BGA |
| XC2C2567FTG256C | 制造商:XILINX 功能描述:Pb Free |
發布緊急采購，3分鐘左右您將得到回復。