- 您現在的位置：買賣IC網 > PDF目錄4168 > XC4005XL-2VQ100I (Xilinx Inc)IC FPGA I-TEMP 3.3V 2SP 100VQFP PDF資料下載
參數資料
| 型號： | XC4005XL-2VQ100I |
| 廠商： | Xilinx Inc |
| 文件頁數： | 42/68頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC FPGA I-TEMP 3.3V 2SP 100VQFP |
| 產品變化通告： | Product Discontinuation 27/Apr/2010 |
| 標準包裝： | 1 |
| 系列： | XC4000E/X |
| LAB/CLB數： | 196 |
| 邏輯元件/單元數： | 466 |
| RAM 位總計： | 6272 |
| 輸入/輸出數： | 77 |
| 門數： | 5000 |
| 電源電壓： | 3 V ~ 3.6 V |
| 安裝類型： | 表面貼裝 |
| 工作溫度： | -40°C ~ 100°C |
| 封裝/外殼： | 100-TQFP |
| 供應商設備封裝： | 100-VQFP（14x14） |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
R
May 14, 1999 (Version 1.6)
6-51
XC4000E and XC4000X Series Field Programmable Gate Arrays
6
Low. During this time delay, or as long as the PROGRAM
input is asserted, the conguration logic is held in a Cong-
uration Memory Clear state. The conguration-memory
frames are consecutively initialized, using the internal oscil-
lator.
At the end of each complete pass through the frame
addressing, the power-on time-out delay circuitry and the
level of the PROGRAM pin are tested. If neither is asserted,
the logic initiates one additional clearing of the congura-
tion frames and then tests the INIT input.
Initialization
During initialization and conguration, user pins HDC, LDC,
INIT and DONE provide status outputs for the system inter-
face. The outputs LDC, INIT and DONE are held Low and
HDC is held High starting at the initial application of power.
The open drain INIT pin is released after the nal initializa-
tion pass through the frame addresses. There is a deliber-
ate delay of 50 to 250
s (up to 10% longer for low-voltage
devices) before a Master-mode device recognizes an inac-
tive INIT. Two internal clocks after the INIT pin is recognized
as High, the FPGA samples the three mode lines to deter-
mine the conguration mode. The appropriate interface
lines become active and the conguration preamble and
data can be loaded.Conguration
The 0010 preamble code indicates that the following 24 bits
represent the length count. The length count is the total
number of conguration clocks needed to load the com-
plete conguration data. (Four additional conguration
clocks are required to complete the conguration process,
as discussed below.) After the preamble and the length
count have been passed through to all devices in the daisy
chain, DOUT is held High to prevent frame start bits from
reaching any daisy-chained devices.
A specic conguration bit, early in the rst frame of a mas-
ter device, controls the conguration-clock rate and can
increase it by a factor of eight. Therefore, if a fast congu-
ration clock is selected by the bitstream, the slower clock
rate is used until this conguration bit is detected.
Each frame has a start eld followed by the frame-congu-
ration data bits and a frame error eld. If a frame data error
is detected, the FPGA halts loading, and signals the error
by pulling the open-drain INIT pin Low. After all congura-
tion frames have been loaded into an FPGA, DOUT again
follows the input data so that the remaining data is passed
on to the next device.
Delaying Conguration After Power-Up
There are two methods of delaying conguration after
power-up: put a logic Low on the PROGRAM input, or pull
the bidirectional INIT pin Low, using an open-collector
(open-drain) driver. (See Figure 46 on page 50.)
A Low on the PROGRAM input is the more radical
approach, and is recommended when the power-supply
rise time is excessive or poorly dened. As long as PRO-
GRAM is Low, the FPGA keeps clearing its conguration
memory. When PROGRAM goes High, the conguration
memory is cleared one more time, followed by the begin-
ning of conguration, provided the INIT input is not exter-
nally held Low. Note that a Low on the PROGRAM input
automatically forces a Low on the INIT output. The XC4000
Series PROGRAM pin has a permanent weak pull-up.
Using an open-collector or open-drain driver to hold INIT
Low before the beginning of conguration causes the
FPGA to wait after completing the conguration memory
clear operation. When INIT is no longer held Low exter-
nally, the device determines its conguration mode by cap-
turing its mode pins, and is ready to start the conguration
process. A master device waits up to an additional 250
s
to make sure that any slaves in the optional daisy chain
have seen that INIT is High.
Start-Up
Start-up is the transition from the conguration process to
the intended user operation. This transition involves a
change from one clock source to another, and a change
from interfacing parallel or serial conguration data where
most outputs are 3-stated, to normal operation with I/O pins
active in the user-system. Start-up must make sure that the
user-logic ‘wakes up’ gracefully, that the outputs become
active without causing contention with the conguration sig-
nals, and that the internal ip-ops are released from the
global Reset or Set at the right time.
Figure 47 describes start-up timing for the three Xilinx fam-
ilies in detail. The conguration modes can use any of the
four timing sequences.
To access the internal start-up signals, place the STARTUP
library symbol.
Start-up Timing
Different FPGA families have different start-up sequences.
The XC2000 family goes through a xed sequence. DONE
goes High and the internal global Reset is de-activated one
CCLK period after the I/O become active.
The XC3000A family offers some exibility. DONE can be
programmed to go High one CCLK period before or after
the I/O become active. Independent of DONE, the internal
global Reset is de-activated one CCLK period before or
after the I/O become active.
The XC4000 Series offers additional exibility. The three
events — DONE going High, the internal Set/Reset being
de-activated, and the user I/O going active — can all occur
in any arbitrary sequence. Each of them can occur one
CCLK period before or after, or simultaneous with, any of
the others. This relative timing is selected by means of soft-
ware options in the bitstream generation software.
Product Obsolete or Under Obsolescence
相關PDF資料 |
PDF描述 |
|---|---|
| XC4005XL-2VQ100C | IC FPGA C-TEMP 3.3V 2SP 100VQFP |
| XC4005XL-2TQ144I | IC FPGA I-TEMP 3.3V 2SPD 144TQFP |
| ABB106DHRR-S621 | CONN EDGECARD EXTEND 212POS .050 |
| XC4005XL-2TQ144C | IC FPGA C-TEMP 3.3V 2SPD 144TQFP |
| XC4005XL-2PQ208I | IC FPGA I-TEMP 3.3V 2SPD 208PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XC4005XL-2VQ100M | 制造商:XILINX 制造商全稱:XILINX 功能描述:XC4000E and XC4000X Series Field Programmable Gate Arrays |
| XC4005XL-3PC84C | 功能描述:IC FPGA C-TEMP 3.3V 3SPD 84-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:XC4000E/X 標準包裝:1 系列:Kintex-7 LAB/CLB數:25475 邏輯元件/單元數:326080 RAM 位總計:16404480 輸入/輸出數:350 門數:- 電源電壓:0.97 V ~ 1.03 V 安裝類型:表面貼裝 工作溫度:0°C ~ 85°C 封裝/外殼:900-BBGA，F(xiàn)CBGA 供應商設備封裝:900-FCBGA（31x31） 其它名稱:122-1789 |
| XC4005XL-3PC84I | 功能描述:IC FPGA I-TEMP 3.3V 3SPD 84-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:XC4000E/X 標準包裝:1 系列:Kintex-7 LAB/CLB數:25475 邏輯元件/單元數:326080 RAM 位總計:16404480 輸入/輸出數:350 門數:- 電源電壓:0.97 V ~ 1.03 V 安裝類型:表面貼裝 工作溫度:0°C ~ 85°C 封裝/外殼:900-BBGA，F(xiàn)CBGA 供應商設備封裝:900-FCBGA（31x31） 其它名稱:122-1789 |
| XC4005XL-3PC84M | 制造商:XILINX 制造商全稱:XILINX 功能描述:XC4000E and XC4000X Series Field Programmable Gate Arrays |
| XC4005XL-3PQ100C | 功能描述:IC FPGA C-TEMP 3.3V 3SPD 100PQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:XC4000E/X 標準包裝:1 系列:Kintex-7 LAB/CLB數:25475 邏輯元件/單元數:326080 RAM 位總計:16404480 輸入/輸出數:350 門數:- 電源電壓:0.97 V ~ 1.03 V 安裝類型:表面貼裝 工作溫度:0°C ~ 85°C 封裝/外殼:900-BBGA，F(xiàn)CBGA 供應商設備封裝:900-FCBGA（31x31） 其它名稱:122-1789 |
發布緊急采購，3分鐘左右您將得到回復。