參數資料
型號: XC4013E-4PQ160C
廠商: Xilinx Inc
文件頁數: 30/68頁
文件大?。?/td> 0K
描述: IC FPGA 576 CLB'S 160-PQFP
產品變化通告: Product Discontinuation 28/Jul/2010
標準包裝: 24
系列: XC4000E/X
LAB/CLB數: 576
邏輯元件/單元數: 1368
RAM 位總計: 18432
輸入/輸出數: 129
門數: 13000
電源電壓: 4.75 V ~ 5.25 V
安裝類型: 表面貼裝
工作溫度: 0°C ~ 85°C
封裝/外殼: 160-BQFP
供應商設備封裝: 160-PQFP(28x28)
其它名稱: 122-1109
R
XC4000E and XC4000X Series Field Programmable Gate Arrays
6-40
May 14, 1999 (Version 1.6)
Table 16: Pin Descriptions
Pin Name
I/O
During
Cong.
I/O
After
Cong.
Pin Description
Permanently Dedicated Pins
VCC
I
Eight or more (depending on package) connections to the nominal +5 V supply voltage
(+3.3 V for low-voltage devices). All must be connected, and each must be decoupled
with a 0.01 - 0.1
F capacitor to Ground.
GND
I
Eight or more (depending on package type) connections to Ground. All must be con-
nected.
CCLK
I or O
I
During configuration, Configuration Clock (CCLK) is an output in Master modes or Asyn-
chronous Peripheral mode, but is an input in Slave mode and Synchronous Peripheral
mode. After configuration, CCLK has a weak pull-up resistor and can be selected as the
Readback Clock. There is no CCLK High or Low time restriction on XC4000 Series de-
vices, except during Readback. See “Violating the Maximum High and Low Time Spec-
ification for the Readback Clock” on page 56 for an explanation of this exception.
DONE
I/O
O
DONE is a bidirectional signal with an optional internal pull-up resistor. As an output, it
indicates the completion of the configuration process. As an input, a Low level on DONE
can be configured to delay the global logic initialization and the enabling of outputs.
The optional pull-up resistor is selected as an option in the XACT
step program that cre-
ates the configuration bitstream. The resistor is included by default.
PROGRAM
I
PROGRAM is an active Low input that forces the FPGA to clear its configuration mem-
ory. It is used to initiate a configuration cycle. When PROGRAM goes High, the FPGA
finishes the current clear cycle and executes another complete clear cycle, before it
goes into a WAIT state and releases INIT.
The PROGRAM pin has a permanent weak pull-up, so it need not be externally pulled
up to Vcc.
User I/O Pins That Can Have Special Functions
RDY/BUSY
O
I/O
During Peripheral mode configuration, this pin indicates when it is appropriate to write
another byte of data into the FPGA. The same status is also available on D7 in Asyn-
chronous Peripheral mode, if a read operation is performed when the device is selected.
After configuration, RDY/BUSY is a user-programmable I/O pin.
RDY/BUSY is pulled High with a high-impedance pull-up prior to INIT going High.
RCLK
O
I/O
During Master Parallel configuration, each change on the A0-A17 outputs (A0 - A21 for
XC4000X) is preceded by a rising edge on RCLK, a redundant output signal. RCLK is
useful for clocked PROMs. It is rarely used during configuration. After configuration,
RCLK is a user-programmable I/O pin.
M0, M1, M2
I
I (M0),
O (M1),
I (M2)
As Mode inputs, these pins are sampled after INIT goes High to determine the configu-
ration mode to be used. After configuration, M0 and M2 can be used as inputs, and M1
can be used as a 3-state output. These three pins have no associated input or output
registers.
During configuration, these pins have weak pull-up resistors. For the most popular con-
figuration mode, Slave Serial, the mode pins can thus be left unconnected. The three
mode inputs can be individually configured with or without weak pull-up or pull-down re-
sistors. A pull-down resistor value of 4.7 k
is recommended.
These pins can only be used as inputs or outputs when called out by special schematic
definitions. To use these pins, place the library components MD0, MD1, and MD2 in-
stead of the usual pad symbols. Input or output buffers must still be used.
TDO
O
If boundary scan is used, this pin is the Test Data Output. If boundary scan is not used,
this pin is a 3-state output without a register, after configuration is completed.
This pin can be user output only when called out by special schematic definitions. To
use this pin, place the library component TDO instead of the usual pad symbol. An out-
put buffer must still be used.
Product Obsolete or Under Obsolescence
相關PDF資料
PDF描述
ASC44DRAN-S734 CONN EDGECARD 88POS .100 R/A PCB
ASC44DRAH-S734 CONN EDGECARD 88POS .100 R/A PCB
IDT71V3577S80PFG IC SRAM 4MBIT 80NS 100TQFP
AMM28DSAI CONN EDGECARD 56POS R/A .156 SLD
AMM10DREN CONN EDGECARD 20POS .156 EYELET
相關代理商/技術參數
參數描述
XC4013E-4PQ160I 功能描述:IC FPGA I-TEMP 5V 4SPD 160-PQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:XC4000E/X 標準包裝:1 系列:Kintex-7 LAB/CLB數:25475 邏輯元件/單元數:326080 RAM 位總計:16404480 輸入/輸出數:350 門數:- 電源電壓:0.97 V ~ 1.03 V 安裝類型:表面貼裝 工作溫度:0°C ~ 85°C 封裝/外殼:900-BBGA,F(xiàn)CBGA 供應商設備封裝:900-FCBGA(31x31) 其它名稱:122-1789
XC4013E-4PQ208C 功能描述:IC FPGA 576 CLB'S 208-PQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:XC4000E/X 產品變化通告:XC4000(E,L) Discontinuation 01/April/2002 標準包裝:24 系列:XC4000E/X LAB/CLB數:100 邏輯元件/單元數:238 RAM 位總計:3200 輸入/輸出數:80 門數:3000 電源電壓:4.5 V ~ 5.5 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 100°C 封裝/外殼:120-BCBGA 供應商設備封裝:120-CPGA(34.55x34.55)
XC4013E-4PQ208I 功能描述:IC FPGA I-TEMP 5V 4SPD 208-PQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:XC4000E/X 標準包裝:1 系列:Kintex-7 LAB/CLB數:25475 邏輯元件/單元數:326080 RAM 位總計:16404480 輸入/輸出數:350 門數:- 電源電壓:0.97 V ~ 1.03 V 安裝類型:表面貼裝 工作溫度:0°C ~ 85°C 封裝/外殼:900-BBGA,F(xiàn)CBGA 供應商設備封裝:900-FCBGA(31x31) 其它名稱:122-1789
XC4013E-4PQ240C 功能描述:IC FPGA C-TEMP 5V 4SPD 240-PQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:XC4000E/X 標準包裝:1 系列:Kintex-7 LAB/CLB數:25475 邏輯元件/單元數:326080 RAM 位總計:16404480 輸入/輸出數:350 門數:- 電源電壓:0.97 V ~ 1.03 V 安裝類型:表面貼裝 工作溫度:0°C ~ 85°C 封裝/外殼:900-BBGA,F(xiàn)CBGA 供應商設備封裝:900-FCBGA(31x31) 其它名稱:122-1789
XC4013E-4PQ240C0167 制造商:Xilinx 功能描述: