- 您現在的位置：買賣IC網 > PDF目錄4044 > XC4036XL-3HQ304C (Xilinx Inc)IC FPGA C-TEMP 3.3V 3SPD 304HQFP PDF資料下載
參數資料
| 型號： | XC4036XL-3HQ304C |
| 廠商： | Xilinx Inc |
| 文件頁數： | 43/68頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC FPGA C-TEMP 3.3V 3SPD 304HQFP |
| 產品變化通告： | XC4000(XL,XLA,E) Discontinuation 15/Nov/2004 |
| 標準包裝： | 12 |
| 系列： | XC4000E/X |
| LAB/CLB數： | 1296 |
| 邏輯元件/單元數： | 3078 |
| RAM 位總計： | 41472 |
| 輸入/輸出數： | 256 |
| 門數： | 36000 |
| 電源電壓： | 3 V ~ 3.6 V |
| 安裝類型： | 表面貼裝 |
| 工作溫度： | 0°C ~ 85°C |
| 封裝/外殼： | 304-BFQFP 裸露焊盤 |
| 供應商設備封裝： | 304-PQFP（40x40） |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
R
XC4000E and XC4000X Series Field Programmable Gate Arrays
6-52
May 14, 1999 (Version 1.6)
The default option, and the most practical one, is for DONE
to go High rst, disconnecting the conguration data source
and avoiding any contention when the I/Os become active
one clock later. Reset/Set is then released another clock
period later to make sure that user-operation starts from
stable internal conditions. This is the most common
sequence, shown with heavy lines in Figure 47, but the
designer can modify it to meet particular requirements.
Normally, the start-up sequence is controlled by the internal
device oscillator output (CCLK), which is asynchronous to
the system clock.
XC4000 Series offers another start-up clocking option,
UCLK_NOSYNC. The three events described above need
not be triggered by CCLK. They can, as a conguration
option, be triggered by a user clock. This means that the
device can wake up in synchronism with the user system.
When the UCLK_SYNC option is enabled, the user can
externally hold the open-drain DONE output Low, and thus
stall all further progress in the start-up sequence until
DONE is released and has gone High. This option can be
used to force synchronization of several FPGAs to a com-
mon user clock, or to guarantee that all devices are suc-
cessfully congured before any I/Os go active.
If either of these two options is selected, and no user clock
is specied in the design or attached to the device, the chip
could reach a point where the conguration of the device is
complete and the Done pin is asserted, but the outputs do
not become active. The solution is either to recreate the bit-
stream specifying the start-up clock as CCLK, or to supply
the appropriate user clock.
Start-up Sequence
The Start-up sequence begins when the conguration
memory is full, and the total number of conguration clocks
received since INIT went High equals the loaded value of
the length count.
The next rising clock edge sets a ip-op Q0, shown in
Figure 48. Q0 is the leading bit of a 5-bit shift register. The
outputs of this register can be programmed to control three
events.
The release of the open-drain DONE output
The change of conguration-related pins to the user
function, activating all IOBs.
The termination of the global Set/Reset initialization of
all CLB and IOB storage elements.
The DONE pin can also be wire-ANDed with DONE pins of
other FPGAs or with other external signals, and can then
be used as input to bit Q3 of the start-up register. This is
called “Start-up Timing Synchronous to Done In” and is
selected by either CCLK_SYNC or UCLK_SYNC.
When DONE is not used as an input, the operation is called
“Start-up Timing Not Synchronous to DONE In,” and is
selected by either CCLK_NOSYNC or UCLK_NOSYNC.
As a conguration option, the start-up control register
beyond Q0 can be clocked either by subsequent CCLK
pulses or from an on-chip user net called STARTUP.CLK.
These signals can be accessed by placing the STARTUP
library symbol.
Start-up from CCLK
If CCLK is used to drive the start-up, Q0 through Q3 pro-
vide the timing. Heavy lines in Figure 47 show the default
timing, which is compatible with XC2000 and XC3000
devices using early DONE and late Reset. The thin lines
indicate all other possible timing options.
Product Obsolete or Under Obsolescence
相關PDF資料 |
PDF描述 |
|---|---|
| 65801-123LF | CLINCHER RECEPTACLE ASSY TIN |
| 65801-121LF | CLINCHER RECEPTACLE ASSY TIN |
| MPC8543EPXANGB | MPU POWERQUICC III 783-PBGA |
| P1013NSN2MHB | IC MPU 1055MHZ 689TEPBGA |
| FMC35DRAS | CONN EDGECARD 70POS .100 R/A |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XC4036XL-3HQ304I | 功能描述:IC FPGA I-TEMP 3.3V 3SPD 304HQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:XC4000E/X 標準包裝:1 系列:Kintex-7 LAB/CLB數:25475 邏輯元件/單元數:326080 RAM 位總計:16404480 輸入/輸出數:350 門數:- 電源電壓:0.97 V ~ 1.03 V 安裝類型:表面貼裝 工作溫度:0°C ~ 85°C 封裝/外殼:900-BBGA，F(xiàn)CBGA 供應商設備封裝:900-FCBGA（31x31） 其它名稱:122-1789 |
| XC4036XLA-07HQ208C | 制造商:Xilinx 功能描述: |
| XC4036XLA-08HQ160I | 制造商:Xilinx 功能描述: |
| XC4036XLA-08HQ208I | 制造商:Xilinx 功能描述: |
| XC4036XLA-08HQ240C | 制造商:Xilinx 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。