參數資料
型號: XC9303E093KR
廠商: TOREX SEMICONDUCTOR LTD.
英文描述: High Efficiency, Synchronous Step-Up & Down DC / DC Controller ICs
中文描述: 高,同步降壓效率最高
文件頁數: 5/20頁
文件大?。?/td> 921K
代理商: XC9303E093KR
5/20
XC9303
Series
OPERATIONAL EXPLANATION
The XC9303 series are synchronous step-up & down DC/DC converter controller ICs with built-in high speed, low ON
resistance drivers.
<Error Amp.>
The error amplifier is designed to monitor the output voltage and it compares the feedback voltage (FB) with the reference
voltage. In response to feedback of a voltage lower than the reference voltage, the output voltage of the error amp.
decreases.
<OSC Generator>
This circuit generates the oscillation frequency, which in turn generates the source clock.
<Ramp Wave Generator>
The ramp wave generator generates a saw-tooth waveform based on outputs from the phase shift generator.
<PWM Comparator>
The PWM Comparator compares outputs from the error amp. and saw-tooth waveform. When the voltage from the error
amp's output is low, the external switch will be set to ON.
<PWM/PFM Controller>
This circuit generates PFM pulses. Control can be switched between PWM control and PWM/PFM automatic switching
control using external signals. The PWM/PFM automatic switching mode is selected when the voltage of the PWM pin is less
than 0.2V, and the control switches between PWM and PFM automatically depending on the load. As the PFM circuit
generates pulses based on outputs from the PWM comparator, shifting between modes occurs smoothly. PWM control mode
is selected when the voltage of the PWM pin is more than 0.65V. Noise is easily reduced with PWM control since the switching
frequency is fixed. Control suited to the application can easily be selected which is useful in audio applications, for example,
where traditionally, efficiencies have been sacrificed during stand-by as a result of using PWM control (due to the noise
problems associated with the PFM mode in stand-by).
<Synchronous, blank logic>
The synchronous, blank logic circuit is to prevent penetration of the transistor connected to EXT1 and EXT2.
<Vref with Soft Start>
The reference voltage, Vref (FB pin voltage)=0.9V, is adjusted and fixed by laser trimming (for output voltage settings, please
refer to next page). To protect against inrush current, when the power is switched on, and also to protect against voltage
overshoot, soft-start time is set internally to 10ms. It should be noted, however, that this circuit does not protect the load
capacitor (C
L
) from inrush current. With the Vref voltage limited and depending upon the input to the error amps, the operation
maintains a balance between the two inputs of the error amps and controls the EXT pin's ON time so that it doesn't increase
more than is necessary.
<Chip Enable Function>
This function controls the operation and shutdown of the IC. When the voltage of the CE pin is 0.2V or less, the mode will be
chip disable, the channel's operations will stop. The EXT1 pin will be kept at a high level (the external P-ch MOSFET will be
OFF) and the EXT2 pin will be kept at a low level (the external N-ch MOSFET will be OFF). When CE pin is in a state of chip
disable, current consumption will be no more than 3.0
μ
A. When the CE pin's voltage is 0.65V or more, the mode will be chip
enable and operations will recommence. With soft-start, 95% of the set output voltage will be reached within 10ms (TYP.)
from the moment of chip enable.
<Output Voltage Setting>
Output voltage can be set by adding external split resistors. Output voltage is determined by the following equation, based on
the values of R
FB11
(R
FB21
) and R
FB12
(R
FB22
). The sum of R
FB11
(R
FB21
) and R
FB12
(R
FB22
) should normally be 1 M
Ω
or less.
V
OUT
= 0.9
×
( R
FB11
+ R
FB12
) / R
FB12
The value of C
FB1
(C
FB2
), speed-up capacitor for phase compensation, should be
fzfb= 1 / (2
×π×
C
FB1
×
R
FB11
)
which is equal
to 12kHz. Adjustments are required from 1kHz to 50kHz depending on the application, value of inductance (L), and value of load
capacity (C
L
).
相關PDF資料
PDF描述
XC9501B095AR 2ch. Step-up DC/DC Controller ICs.
XC9501B09AL 2ch. Step-up DC/DC Controller ICs.
XC9501B09AR 2ch. Step-up DC/DC Controller ICs.
XC9501 2ch. Step-up DC/DC Controller ICs.
XC9501B093AL 2ch. Step-up DC/DC Controller ICs.
相關代理商/技術參數
參數描述
XC9306B05G0R-G 功能描述:Buck-Boost Switching Regulator IC Positive Adjustable 0.8V 1 Output 800mA (Switch) 20-UFBGA, WLBGA 制造商:torex semiconductor ltd 系列:- 包裝:剪切帶(CT) 零件狀態:有效 功能:升壓/降壓 輸出配置:正 拓?fù)?降壓-升壓 輸出類型:可調式 輸出數:1 電壓 - 輸入(最小值):2.5V 電壓 - 輸入(最大值):5.5V 電壓 - 輸出(最小值/固定):0.8V 電壓 - 輸出(最大值):5V 電流 - 輸出:800mA(開關) 頻率 - 開關:6MHz 同步整流器:是 工作溫度:-40°C ~ 85°C(TA) 安裝類型:表面貼裝 封裝/外殼:20-UFBGA,WLBGA 供應商器件封裝:WLP-20-01(1.94x2.15) 標準包裝:1
XC93222CFN 制造商:Freescale Semiconductor 功能描述:
XC9401 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Off-line Controllers for LED Ligh
XC9401_13 制造商:TOREX 制造商全稱:Torex Semiconductor 功能描述:Off-line Controllers for LED Lighting
XC9401A605MR-G 制造商:TOREX 制造商全稱:Torex Semiconductor 功能描述:Off-line Controllers for LED Lighting