參數資料
型號: XCR3384XL-10PQ208C
廠商: Xilinx Inc
文件頁數: 8/12頁
文件大?。?/td> 0K
描述: IC CPLD 3.3V ZERO PWR 208-PQFP
標準包裝: 24
系列: CoolRunner XPLA3
可編程類型: 系統內可編程(最少 1K 次編程/擦除循環)
最大延遲時間 tpd(1): 9.0ns
電壓電源 - 內部: 3 V ~ 3.6 V
邏輯元件/邏輯塊數目: 24
宏單元數: 384
門數: 9000
輸入/輸出數: 172
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 208-BFQFP
供應商設備封裝: 208-PQFP(28x28)
包裝: 托盤
其它名稱: XCR3384XL10PQ208C
CoolRunner XPLA3 CPLD
DS012 (v2.5) May 26, 2009
Product Specification
R
mented in the buried macrocell can be fed back to the ZIA
via the macrocell feedback path.
If a macrocell pin is configured as a registered input, there is
a direct path to the register to provide a fast input setup
time. If the macrocell is configured as a latch, the register
clock input functions as the latch enable, with the latch
transparent when this signal is High. The hardwired clock
enable is non-functional when the macrocell is configured
as a latch.
I/O Cell
The OE (Output Enable) multiplexer has eight possible
modes (Figure 6). When the I/O Cell is configured as an
input (or 3-stated output), a half latch feature exists. This
half latch pulls the input High (through a weak pull-up) if the
input should float and cross the threshold. This protects the
input from staying in the linear region and causing an
increased amount of power consumption. This same weak
pull-up can be enabled in software such that it is always on
when the I/O Cell is configured as an input. This weak pull
up is automatically turned on when a pin is unused by the
design.
The I/O Cell is 5V tolerant when the device is powered.
Each output has independent slew rate control (fast or slow)
which assists in reducing EMI emissions.
See individual device data sheets for 3.3V PCI electrical
specification compatibility.
Note that an I/O macrocell used as buried logic that does
not have the I/O pin used for input is considered to be
unused, and the weak pull-up resistors will be turned on. It
is recommended that any unused I/O pins on the CoolRun-
ner XPLA3 family of CPLDs be left unconnected. Dedicated
input pins (CLKx/INx) do not have on-chip weak pull-up
resistors; therefore unused dedicated input pins must have
external termination. As with all CMOS devices, do not
allow inputs to float.
Figure 5: XPLA3 Macrocell Architecture
Global CLK
Universal CLK
P-term CLK
CT [4:7]
ds012_05_122299
Universal PST
CT [0:5]
Universal RST
CT [0:5]
To ZIA
To I/O
PAD
Note: Global CLK signals come from pins.
To ZIA
VFM
RST
PST
D/T/L
CLKEn
Q
CT4
P-term
48
PLA OR Term
From PT Array
1
Figure 6: I/O Cell
GND (Weak P.U.)
VCC
Universal OE
CT
GND
OE [2:0]
To Macrocell / ZIA
From Macrocell
I/O Pin
WP
Slew
Control
OE
Decode
0
1
2
3
4
5
6
7
I/O Pin
State
3-State
Function CT0
Function CT1
Function CT2
Function CT6
Universal OE
Enable
Weak P.U.
ds012_06_121699
Weak Pull-up
OE = 7
VCC
3
4
相關PDF資料
PDF描述
TNY264G IC OFFLINE SWIT OTP OCP HV 8SMD
XCR3384XL-12FT256C IC CPLD 3.3V ZERO PWR 256-BGA
MAX6698EE38+T IC TEMP MONITOR I2C 7CH 16QSOP
PQ1R33 IC REG LDO 3.3V .15A SOT-23L
XC2C512-10FGG324I IC CR-II CPLD 512MCRCELL 324FBGA
相關代理商/技術參數
參數描述
XCR3384XL-10PQ208CES 制造商:Xilinx 功能描述:
XCR3384XL-10PQ208I 功能描述:IC CPLD 3.3V ZERO PWR 208-PQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - CPLD(復雜可編程邏輯器件) 系列:CoolRunner XPLA3 標準包裝:40 系列:ispMACH® 4000C 可編程類型:系統內可編程 最大延遲時間 tpd(1):5.0ns 電壓電源 - 內部:1.65 V ~ 1.95 V 邏輯元件/邏輯塊數目:32 宏單元數:512 門數:- 輸入/輸出數:128 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:176-LQFP 供應商設備封裝:176-TQFP(24x24) 包裝:托盤
XCR3384XL-10PQG208C 制造商:Xilinx 功能描述:CPLD COOLRUNNER XPLA3 9K GATES 384 MCRCLLS 125MHZ COMM 0.35U - Trays
XCR3384XL-10PQG208I 制造商:Xilinx 功能描述:CPLD COOLRUNNER XPLA3 9K GATES 384 MCRCLLS 125MHZ IND 0.35UM - Trays
XCR3384XL-10TQ144C 制造商:Xilinx 功能描述:CPLD COOLRUNNER XPLA3 9K GATES 384 MCRCLLS 125MHZ 0.35UM 3.3 - Trays