- 您現在的位置：買賣IC網 > PDF目錄376455 > XR-2206P (EXAR CORP) Waveform Generator/Support PDF資料下載
參數資料
| 型號： | XR-2206P |
| 廠商： | EXAR CORP |
| 元件分類： | 運動控制電子 |
| 英文描述： | Waveform Generator/Support |
| 中文描述： | SQUARE; TRIANGULAR; SINE; SAWTOOTH; PULSE, 1 MHz, WAVEFORM GENERATION, PDIP16 |
| 封裝： | 0.300 INCH, PLASTIC, DIP-16 |
| 文件頁數： | 10/16頁 |
| 文件大小： | 191K |
| 代理商： | XR-2206P |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁
XR-2206
10
Rev. 1.03
Figure 14. Circuit for Pulse and Ramp Generation.
1
5
6
7
8
9
11
3
2
13
14
15
16
4
10
12
XR-2206
1 F
V
CC
C
R
1
R
2
5.1K
5.1K
5.1K
10 F
1 F
R
3
24K
V
CC
V
CC
Mult.
And
Sine
Shaper
VCO
+1
+
+
Current
Switches
f
2
C
1
R
1
R
2
R
1
R
1
R
2
Duty Cycle =
Sawtooth Output
Pulse Output
Frequency-Shift Keying
The XR-2206 can be operated with two separate timing
resistors, R
1
and R
2
, connected to the timing Pin 7 and 8,
respectively, as shown in Figure 13.Depending on the
polarity of the logic signal at Pin 9, either one or the other
of these timing resistors is activated. If Pin 9 is
open-circuited or connected to a bias voltage
R
1
is activated. Similarly, if the voltage level at Pin 9 is
1V, only R
2
is activated. Thus, the output frequency can
be keyed between two levels. f
1
and f
2
, as:
2V, only
f
1
= 1/R
1
C and f
2
= 1/R
2
C
For split-supply operation, the keying voltage at Pin 9 is
referenced to V
-
.
Output DC Level Control
The dc level at the output (Pin 2) is approximately the
same as the dc bias at Pin 3. In Figure 11 Figure 12and
Figure 13 Pin 3 is biased midway between V+ and
ground, to give an output dc level of
V
+
/2.
APPLICATIONS INFORMATION
Sine Wave Generation
Without External Adjustment
Figure 11shows the circuit connection for generating a
sinusoidal output from the XR-2206. The potentiometer,
R
1
at Pin 7, provides the desired frequency tuning. The
maximum output swing is greater than V
+
/2, and the
typical distortion (THD) is < 2.5%. If lower sine wave
distortion is desired, additional adjustments can be
provided as described in the following section.
The circuit of Figure 11can be converted to split-supply
operation, simply by replacing all ground connections
with V
-
. For split-supply operation, R
3
can be directly
connected to ground.
相關PDF資料 |
PDF描述 |
|---|---|
| XR2209 | Voltage-Controlled Oscillator |
| XR-2209 | Voltage-Controlled Oscillator |
| XR-2209CN | Voltage-Controlled Oscillator |
| XR-2209CP | Voltage-Controlled Oscillator |
| XR-2209M | Voltage-Controlled Oscillator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR2207 | 制造商:EXAR 制造商全稱:EXAR 功能描述:Voltage-Controlled Oscillator |
| XR-2207 | 制造商:EXAR 制造商全稱:EXAR 功能描述:Voltage-Controlled Oscillator |
| XR2207CN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Waveform Generator/Support |
| XR-2207CP | 制造商:EXAR 制造商全稱:EXAR 功能描述:Voltage-Controlled Oscillator |
| XR-2207D | 制造商:EXAR 制造商全稱:EXAR 功能描述:Voltage-Controlled Oscillator |
發布緊急采購，3分鐘左右您將得到回復。