
XR-T7288
6
Rev. 1.01
ELECTRICAL CHARACTERISTICS
(CONT’D)
Symbol
Parameter
Min.
Typ.
Max.
Unit
Conditions
Receiver Specifications (Cont’d)
Input Transformer Turns Ratio
1:1.9
1:2.0
1:2.1
Input Resistance, RI or TI, Each
Input to Ground
Jitter (20Hz-100kHz)
0.9
3.0
k
Receive Plus Transmit
Jitter at T2/R2
Transmit Jitter at T2/R2
0.06
0.09
U.I. peak-to-peak
0.012
0.04
U.I. peak-to-peak
Power Dissipation
5
(TA=-40
°
C to +85
°
C, V
DD
=5.0 V
Power Dissipation
10%)
Pdis
75 (ZS = 0)
190
290
mW
All 1s transmit and
Pdis
120 (ZS = 1)
170
260
mW
receive data, V
DD
=5.5V
Power Dissipation:
Pdis
75 (ZS = 0)
170
mW
All 1s transmit and
Pdis
120 (ZS = 1)
150
mW
receive data, V
DD
=5.0V
Power Dissipation:
Pdis
75 (ZS = 0)
108
mW
PRBS (50% 1s) transmit and
Pdis
120 (ZS = 1)
100
mW
receive data, V
DD
=5.0V
Notes
1
Digital outputs drive purely capacitive loads to full output levels (V
DD
D, GNDD)
2
Percentage of the nominal pulse amplitude.
3
Measured at T1, R1 (V peak-to-zero, GND reference)
4
Transfer characteristics (1/4 input)
5
All measurements are with a matched-impedance transmit interface (see Figure 3. and Figure 4.) and with V
DD
or GND applied to
digital input leads.
Internal pull-up devices are provided on the following nput eads: LP1, LP2, LP3 and ALMT. Internal pull-down devices are provided
on the following leads: SD, RBC, HDB3/TNDATA, TBC, SR/DR, FLM, and ZS. The internal pull-up or pull-down devices require the
input to source or sink to be no more than 20
μ
A.
Specifications are subject to change without notice
ABSOLUTE MAXIMUM RATINGS
DC Supply Voltage (V
DD
)
Power Dissipation (Pdis)
Storage Temperature (Tstg)
-0.5V to +6.5V
500mW
-65
°
C to +125
°
C
. . . . . . . . . . .
. . . . . . . . . . . . . . . . .
. . . . . . .
Maximum Voltage (any pin) with Respect
to V
DD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Minimum Voltage (any pin) with Respect to GND
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Allowable Voltages
(T1, R1) with Respect to GND
0.5V
-0.5V
-5.0V to 5.0V
. . . . . .
Stresses n excess of the Absolute Maximum Ratings can cause permanent damage to the device. These are absolute stress ratings
only. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operation sec-
tions of the data sheet. Exposure to Absolute Maximum Ratings for extended periods can adversely affect device reliability.
pin assignment ordering information