- 您現在的位置：買賣IC網 > PDF目錄376453 > XR16C2850CJ (EXAR CORP) DUAL UART WITH 128-byte FIFO’s AND RS-485 HALF DUPLEX CONTROL PDF資料下載
參數資料
| 型號： | XR16C2850CJ |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | DUAL UART WITH 128-byte FIFO’s AND RS-485 HALF DUPLEX CONTROL |
| 中文描述： | 2 CHANNEL(S), 6.25M bps, SERIAL COMM CONTROLLER, PQCC44 |
| 封裝： | PLASTIC, LCC-44 |
| 文件頁數： | 22/43頁 |
| 文件大小： | 611K |
| 代理商： | XR16C2850CJ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
á
3.3V AND 5V DUART WITH 128-BYTE FIFO
XR16C2850
REV. 2.0.0
22
4.4.2
LSR interrupt is cleared by a read to the LSR regis-
ter (but flags and tags not cleared until character(s)
that generated the interrupt(s) has been emptied or
cleared from FIFO).
RXRDY interrupt is cleared by reading data until
FIFO falls below the trigger level.
RXRDY Time-out interrupt is cleared by reading
RHR.
Interrupt Clearing:
TXRDY interrupt is cleared by a read to the ISR
register or writing to THR.
MSR interrupt is cleared by a read to the MSR reg-
ister.
Xoff or Special character interrupt is cleared by a
read to ISR.
RTS# and CTS# flow control interrupts are cleared
by a read to the MSR register.
ISR[0]: Interrupt Status
Logic 0 = An interrupt is pending and the ISR con-
tents may be used as a pointer to the appropriate
interrupt service routine.
Logic 1 = No interrupt pending (default condition).
ISR[3:1]: Interrupt Status
These bits indicate the source for a pending interrupt
at interrupt priority levels (See Interrupt Source
Table 9).
ISR[5:4]: Interrupt Status
These bits are enabled when EFR bit-4 is set to a log-
ic 1. ISR bit-4 indicates that the receiver detected a
data match of the Xoff character(s). Note that once
set to a logic 1, the ISR bit-4 will stay a logic 1 until a
Xon character is received. ISR bit-5 indicates that
CTS# or RTS# has changed state.
ISR[7:6]: FIFO Enable Status
These bits are set to a logic 0 when the FIFOs are
disabled. They are set to a logic 1 when the FIFOs
are enabled.
4.5
FIFO C
ONTROL
R
EGISTER
(FCR) - W
RITE
-O
NLY
This register is used to enable the FIFOs, clear the
FIFOs, set the transmit/receive FIFO trigger levels,
and select the DMA mode. The DMA, and FIFO
modes are defined as follows:
FCR[0]: TX and RX FIFO Enable
Logic 0 = Disable the transmit and receive FIFO
(default).
Logic 1 = Enable the transmit and receive FIFOs.
This bit must be set to logic 1 when other FCR bits
are written or they will not be programmed.
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No receive
FIFO
reset (default).
Logic 1 = Reset the receive FIFO pointers and
FIFO level counter logic (the receive shift register is
not cleared or altered). This bit will return to a logic
0 after resetting the FIFO.
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers and
FIFO level counter logic (the transmit shift register
is not cleared or altered). This bit will return to a
logic 0 after resetting the FIFO.
T
ABLE
9: I
NTERRUPT
S
OURCE
AND
P
RIORITY
L
EVEL
P
RIORITY
ISR R
EGISTER
S
TATUS
B
ITS
S
OURCE
OF
INTERRUPT
L
EVEL
B
IT
-5
B
IT
-4
B
IT
-3
B
IT
-2
B
IT
-1
B
IT
-0
1
0
0
0
1
1
0
LSR (Receiver Line Status Register)
2
0
0
1
1
0
0
RXRDY (Receive Data Time-out)
3
0
0
0
1
0
0
RXRDY (Received Data Ready)
4
0
0
0
0
1
0
TXRDY (Transmit Ready)
5
0
0
0
0
0
0
MSR (Modem Status Register)
6
0
1
0
0
0
0
RXRDY (Received Xoff or Special character)
7
1
0
0
0
0
0
CTS#, RTS# change of state
-
0
0
0
0
0
1
None (default)
相關PDF資料 |
PDF描述 |
|---|---|
| XR16C2850CM | DUAL UART WITH 128-byte FIFO’s AND RS-485 HALF DUPLEX CONTROL |
| XR16C2850CP | DUAL UART WITH 128-byte FIFO’s AND RS-485 HALF DUPLEX CONTROL |
| XR16C2850IJ | DUAL UART WITH 128-byte FIFO’s AND RS-485 HALF DUPLEX CONTROL |
| XR16C2850IM | DUAL UART WITH 128-byte FIFO’s AND RS-485 HALF DUPLEX CONTROL |
| XR16C2850IP | DUAL UART WITH 128-byte FIFO’s AND RS-485 HALF DUPLEX CONTROL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16C2850CJ-0A-EB | 功能描述:UART 接口集成電路 Supports C2850 44 ld PLCC, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16C2850CJ44 | 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V AND 5V DUART WITH 128-BYTE FIFO |
| XR16C2850CJ-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16C2850CJTR-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16C2850CM | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。