- 您現在的位置：買賣IC網 > PDF目錄376454 > XR16L2450 (Exar Corporation) 2.25V TO 5.5V DUART PDF資料下載
參數資料
| 型號： | XR16L2450 |
| 廠商： | Exar Corporation |
| 英文描述： | 2.25V TO 5.5V DUART |
| 中文描述： | 2.25V至5.5V的杜阿爾特 |
| 文件頁數： | 3/30頁 |
| 文件大小： | 511K |
| 代理商： | XR16L2450 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
xr
REV. 1.1.0
XR16L2450
2.25V TO 5.5V DUART
3
PACKAGE PIN DESCRIPTIONS
PIN DESCRIPTIONS
N
AME
44-PLCC
P
IN
#
48-TQFP
P
IN
#
T
YPE
D
ESCRIPTION
DATA BUS INTERFACE
A2
A1
A0
29
30
31
26
27
28
I
Address data lines [2:0]. These 3 address lines select one of the inter-
nal registers in UART channel A/B during a data bus transaction.
D7
D6
D5
D4
D3
D2
D1
D0
9
8
7
6
5
4
3
2
3
2
1
48
47
46
45
44
IO
Data bus lines [7:0] (bidirectional).
IOR#
24
19
I
Input/Output Read Strobe (active low). The falling edge instigates an
internal read cycle and retrieves the data byte from an internal register
pointed to by the address lines [A2:A0]. The data byte is placed on the
data bus to allow the host processor to read it on the rising edge.
IOW#
20
15
I
Input/Output Write Strobe (active low). The falling edge instigates an
internal write cycle and the rising edge transfers the data byte on the
data bus to an internal register pointed by the address lines.
CSA#
16
10
I
UART channel A select (active low) to enable UART channel A in the
device for data bus operation.
CSB#
17
11
I
UART channel B select (active low) to enable UART channel B in the
device for data bus operation.
INTA
33
30
O
UART channel A Interrupt output. The output state is defined by the
user and through the software setting of MCR[3]. INTA is set to the
active mode and OP2A# output to a logic 0 when MCR[3] is set to a
logic 1. INTA is set to the three state mode and OP2A# to a logic 1
when MCR[3] is set to a logic 0 (default).
INTB
32
29
O
UART channel B Interrupt output. The output state is defined by the
user and through the software setting of MCR[3]. INTB is set to the
active mode and OP2B# output to a logic 0 when MCR[3] is set to a
logic 1. INTB is set to the three state mode and OP2B# to a logic 1
when MCR[3] is set to a logic 0 (default).
MODEM OR SERIAL I/O INTERFACE
TXA
13
7
O
UART channel A Transmit Data. If it is not used, leave it unconnected.
RXA
11
5
I
UART channel A Receive Data. Normal receive data input must idle at
logic 1 condition. If it is not used, tie it to VCC or pull it high via a 100k
ohm resistor.
RTSA#
36
33
O
UART channel A Request-to-Send (active low) or general purpose out-
put. If it is not used, leave it unconnected.
相關PDF資料 |
PDF描述 |
|---|---|
| XR16L2450IJ | 97-3108A20-29S-KIT |
| XR16L2450IM | 2.25V TO 5.5V DUART |
| XR16L2550IJ | LOW VOLTAGE DUART WITH 16-BYTE FIFO |
| XR16L2550IL | LOW VOLTAGE DUART WITH 16-BYTE FIFO |
| XR16L2550IM | LOW VOLTAGE DUART WITH 16-BYTE FIFO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16L2450_05 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART |
| XR16L2450IJ | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART |
| XR16L2450IJ-0A-EB | 功能描述:UART 接口集成電路 Supports L2450 44 ld PLCC, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L2450IJ-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L2450IM | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART |
發布緊急采購，3分鐘左右您將得到回復。