參數資料
型號: XR16L2551IL
廠商: EXAR CORP
元件分類: 微控制器/微處理器
英文描述: LOW VOLTAGE DUART WITH POWERSAVE
中文描述: 2 CHANNEL(S), 3.125M bps, SERIAL COMM CONTROLLER, QCC32
封裝: 5 X 5 MM, 0.90 MM HEIGHT, QFN-32
文件頁數: 3/48頁
文件大小: 287K
代理商: XR16L2551IL
á
REV. 1.0.0
XR16L2551
LOW VOLTAGE DUART WITH POWERSAVE
3
PIN DESCRIPTIONS
Pin Description
N
AME
32-QFN
P
IN
#
48-TQFP
P
IN
#
T
YPE
D
ESCRIPTION
DATA BUS INTERFACE
A2
A1
A0
18
19
20
26
27
28
I
Address data lines [2:0]. These 3 address lines select one of the inter-
nal registers in UART channel A/B during a data bus transaction.
D7
D6
D5
D4
D3
D2
D1
D0
2
1
32
31
30
29
28
27
3
2
1
48
47
46
45
44
IO
Data bus lines [7:0] (bidirectional).
IOR#
(VCC)
14
19
I
When 16/68# pin is at logic 1, the Intel bus interface is selected and this
input becomes read strobe (active low). The falling edge instigates an
internal read cycle and retrieves the data byte from an internal register
pointed by the address lines [A2:A0], puts the data byte on the data bus
to allow the host processor to read it on the rising edge.
When 16/68# pin is at logic 0, the Motorola bus interface is selected
and this input is not used and should be connected to VCC.
IOW#
(R/W#)
12
15
I
When 16/68# pin is at logic 1, it selects Intel bus interface and this input
becomes write strobe (active low). The falling edge instigates the inter-
nal write cycle and the rising edge transfers the data byte on the data
bus to an internal register pointed by the address lines.
When 16/68# pin is at logic 0, the Motorola bus interface is selected
and this input becomes read (logic 1) and write (logic 0) signal.
CSA#
(CS#)
7
10
I
When 16/68# pin is at logic 1, this input is chip select A (active low) to
enable channel A in the device.
When 16/68# pin is at logic 0, this input becomes the chip select (active
low) for the Motorola bus interface.
CSB#
(A3)
8
11
I
When 16/68# pin is at logic 1, this input is chip select B (active low) to
enable channel B in the device.
When 16/68# pin is at logic 0, this input becomes address line A3
which is used for channel selection in the Motorola bus interface. Input
logic 0 selects channel A and logic 1 selects channel B.
INTA
(IRQ#)
22
30
O
When 16/68# pin is at logic 1 for Intel bus interface, this output
becomes channel A interrupt output. The output state is defined by the
user through the software setting of MCR[3]. INTA is set to the active
mode and OP2A# output to a logic 0 when MCR[3] is set to a logic 1.
INTA is set to the three state mode and OP2A# to a logic 1 when
MCR[3] is set to a logic 0. See MCR[3].
When 16/68# pin is at logic 0 for Motorola bus interface, this output
becomes device interrupt output (active low, open drain). An external
pull-up resistor is required for proper operation.
相關PDF資料
PDF描述
XR16L2551IM LOW VOLTAGE DUART WITH POWERSAVE
XR16L2552IJ 2.25V TO 5.5V DUART WITH 16-BYTE FIFO
XR16L2552IM 2.25V TO 5.5V DUART WITH 16-BYTE FIFO
XR16L2552 2.25V TO 5.5V DUART WITH 16-BYTE FIFO
XR16L2750CJ 2.25V TO 5.5V DUART WITH 64-BYTE FIFO
相關代理商/技術參數
參數描述
XR16L2551IL-0A-EB 功能描述:UART 接口集成電路 Supports L2551 32pin QFN, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L2551IL-0B-EB 功能描述:UART 接口集成電路 Supports L2551 32pin QFN, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L2551IL-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L2551ILTR-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L2551IM 制造商:EXAR 制造商全稱:EXAR 功能描述:LOW VOLTAGE DUART WITH POWERSAVE