- 您現在的位置：買賣IC網 > PDF目錄3762 > XR16L2551ILTR-F (Exar Corporation)IC UART FIFO 16B DUAL 32QFN PDF資料下載
參數資料
| 型號： | XR16L2551ILTR-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 13/49頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO 16B DUAL 32QFN |
| 標準包裝： | 3,000 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 16 字節 |
| 規程： | RS232，RS485 |
| 電源電壓： | 2.25 V ~ 5.5 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-QFN 裸露焊盤（5x5） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
XR16L2551
20
LOW VOLTAGE DUART WITH POWERSAVE
REV. 1.1.3
2.17
Sleep Mode with Auto Wake-Up and PowerSave Feature
The L2551 supports low voltage system designs, hence, a sleep mode with auto wake-up and PowerSave
feature is included to reduce power consumption when the device is not actively used.
2.17.1
Sleep Mode
All of these conditions must be satisfied for the L2551 to enter sleep mode:
■ no interrupts pending for both channels of the L2551 (ISR bit-0 = 1)
■ divisor is a non-zero value (ie. DLL = 0x1)
■ sleep mode of both channels are enabled (IER bit-4 = 1)
■ modem inputs are not toggling (MSR bits 0-3 = 0)
■ RX input pins are idling at a logic 1
The L2551 stops its crystal oscillator to conserve power in the sleep mode. User can check the XTAL2 pin for
no clock output as an indication that the device has entered the sleep mode.
The L2551 resumes normal operation by any of the following when PowerSave mode is disabled:
■ a receive data start bit transition (logic 1 to 0)
■ a data byte is loaded to the transmitter, THR or FIFO
■ a change of logic state on any of the modem or general purpose serial inputs: CTS#, DSR#, CD#, RI#
If the L2551 is awakened by any one of the above conditions, it will return to the sleep mode automatically after
all interrupting conditions have been serviced and cleared. If the L2551 is awakened by the modem inputs, a
read to the MSR is required to reset the modem inputs. In any case, the sleep mode will not be entered while
an interrupt is pending from channel A or B. The L2551 will stay in the sleep mode of operation until it is
disabled by setting IER bit-4 to a logic 0.
A word of caution: owing to the starting up delay of the crystal oscillator after waking up from sleep mode, the
first few receive characters may be lost. The number of characters lost during the restart also depends on your
operating data rate. More characters are lost when operating at higher data rate. Also, it is important to keep
RX A/B inputs idling at logic 1 or “marking” condition during sleep mode to avoid receiving a “break” condition
upon the restart. This may occur when the external interface transceivers (RS-232, RS-485 or another type)
are also put to sleep mode and cannot maintain the “marking” condition. To avoid this, the designer can use a
47k-100k ohm pull-up resistor on the RXA and RXB pins.
2.17.2
PowerSave Feature
If the address lines, data bus lines, IOW#, IOR#, CSA#, CSB#, and modem input lines remain steady when the
L2551 is in sleep mode, the maximum current will be in the microamp range as specified in the DC Electrical
Characteristics on page 36. If the input lines are floating or are toggling while the L2551 is in sleep mode, the
current can be up to 100 times more. If not using the PowerSave feature, then an external buffer would be
required to keep the address and data bus lines from toggling or floating to achieve the low current. But if the
PowerSave feature is enabled (pin 12 of the 48-TQFP or pin 9 of the 32-QFN is connected to VCC), this will
eliminate the need for an external buffer by internally isolating the address, data and control signals (see
Figure 1 on page 1) from other bus activities that could cause wasteful power drain.
The L2551 enters
PowerSave mode when the PWRSAVE pin is connected to VCC and the L2551 is in sleep mode (see Sleep
Mode section above).
Since PowerSave mode isolates the address, data and control signals, the device will wake-up by:
■ a receive data start bit transition (logic 1 to 0)
■ a change of logic state on any of the modem or general purpose serial inputs: CTS#, DSR#, CD#, RI#
The L2551 will return to the PowerSave mode automatically after a read to the MSR (to reset the modem
inputs) and all interrupting conditions have been serviced and cleared. The L2551 will stay in the PowerSave
mode of operation until it is disabled by setting IER bit-4 to a logic 0 and/or the PowerSave pin is connected to
GND.
相關PDF資料 |
PDF描述 |
|---|---|
| XR16L2750IMTR-F | IC UART FIFO 64B DUAL 48TQFP |
| XR16L2552IJTR-F | IC UART FIFO 16B DUAL 44PLCC |
| ST16C2550CQ48TR-F | IC UART FIFO 16B DUAL 48TQFP |
| ATMEGA168-15MT1 | MCU AVR 16K FLASH 15MHZ 32-QFN |
| ATMEGA168-15MT | MCU AVR 16K FLASH 15MHZ 32-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16L2551IM | 制造商:EXAR 制造商全稱:EXAR 功能描述:LOW VOLTAGE DUART WITH POWERSAVE |
| XR16L2551IM-0A-EB | 功能描述:UART 接口集成電路 Supports L2551 48 ld TQFP, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L2551IM-0B-EB | 功能描述:UART 接口集成電路 Supports L2551 48 ld TQFP, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L2551IM-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L2551IMTR-F | 制造商:Exar Corporation 功能描述:UART 2-CH 16Byte FIFO 2.5V/3.3V/5V 48-Pin TQFP T/R 制造商:Exar Corporation 功能描述:XR16L2551IMTR-F |
發布緊急采購，3分鐘左右您將得到回復。