REV. 1.2.1 14 2.14 Auto RTS (Hardware) Flow Control Automatic RTS hardware flow control is u" />
參數資料
型號： XR16L2752CJ-F
廠商： Exar Corporation
文件頁數： 6/49頁
文件大小： 0K
描述： IC UART FIFO 64B DUAL 44PLCC
標準包裝： 27
特點： *
通道數： 2，DUART
FIFO's： 64 字節
規程： RS232，RS485
電源電壓： 2.25 V ~ 5.5 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 44-LCC（J 形引線）
供應商設備封裝： 44-PLCC（16.59x16.59）
包裝： 管件
XR16L2752
xr
2.25V TO 5.5V DUART WITH 64-BYTE FIFO
REV. 1.2.1
14
2.14
Auto RTS (Hardware) Flow Control
Automatic RTS hardware flow control is used to prevent data overrun to the local receiver FIFO. The RTS#
output is used to request remote unit to suspend/resume data transmission. The auto RTS flow control
features is enabled to fit specific application requirement (see Figure 11):
Enable auto RTS flow control using EFR bit-6.
The auto RTS function must be started by asserting RTS# output pin (MCR bit-1 to logic 1 after it is enabled).
If using the Auto RTS interrupt:
Enable RTS interrupt through IER bit-6 (after setting EFR bit-4). The UART issues an interrupt when the
RTS# pin makes a transition from low to high: ISR bit-5 will be set to logic 1.
2.15
Auto RTS Hysteresis
The 2752 has a new feature that provides flow control trigger hysteresis while maintaining compatibility with
the XR16C850, ST16C650A and ST16C550 family of UARTs. With the Auto RTS function enabled, an interrupt
is generated when the receive FIFO reaches the programmed RX trigger level. The RTS# pin will not be forced
HIGH (RTS off), until the receive FIFO reaches the upper limit of the hysteresis level. The RTS# pin will return
LOW after the RX FIFO is unloaded to the lower limit of the hysteresis level. Under the above described
conditions, the 2752 will continue to accept data until the receive FIFO gets full. The Auto RTS function is
initiated when the RTS# output pin is asserted LOW (RTS On). Table 13 shows the complete details for the
Auto RTS# Hysteresis levels. Please note that this table is for programmable trigger levels only (Table D). The
hysteresis values for Tables A-C are the next higher and next lower trigger levels in Tables A-C.
2.16
Auto CTS Flow Control
Automatic CTS flow control is used to prevent data overrun to the remote receiver FIFO. The CTS# input is
monitored to suspend/restart the local transmitter. The auto CTS flow control feature is selected to fit specific
application requirement (see Figure 11):
Enable auto CTS flow control using EFR bit-7.
If using the Auto CTS interrupt:
Enable CTS interrupt through IER bit-7 (after setting EFR bit-4). The UART issues an interrupt when the
CTS# pin is de-asserted (HIGH): ISR bit-5 will be set to 1, and UART will suspend transmission as soon as
the stop bit of the character in process is shifted out. Transmission is resumed after the CTS# input is re-
asserted (LOW), indicating more data may be sent.
相關PDF資料
PDF描述
XR16L570IL24-F IC UART FIFO 16B 24QFN
XR16L580IM-F IC UART FIFO 16B 48TQFP
XR16L651IM-F IC UART FIFO 32B 48TQFP
XR16L784IV-F IC UART 8B 3.3V QUAD 64LQFP
XR16L788IQ-F IC UART 64B 3.3V OCTAL 100QFP
相關代理商/技術參數
參數描述
XR16L2752CJTR-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L2752IJ 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART WITH 64-BYTE FIFO
XR16L2752IJ-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L2752IJTR-F 制造商:Exar Corporation 功能描述:XR16L2752 Series 6.25 Mbps 5.5 V Dual UART With 64-Byte FIFO - PLCC-44
XR16L570 制造商:EXAR 制造商全稱:EXAR 功能描述:SMALLEST 1.62V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*