參數資料
型號： XR16L570IL32TR-F
廠商： Exar Corporation
文件頁數： 19/47頁
文件大?。?/td> 0K
描述： IC UART FIFO 16B 32QFN
標準包裝： 3,000
特點： *
通道數： 1，UART
FIFO's： 16 字節
規程： RS232，RS422
電源電壓： 1.62 V ~ 5.5 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 32-VFQFN 裸露焊盤
供應商設備封裝： 32-QFN 裸露焊盤（5x5）
包裝： 帶卷 (TR)
XR16L570
26
SMALLEST 1.62V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE
REV. 1.0.1
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[3]: DMA Mode Select (Legacy)
This bit has no function and should be left at ’0’.
FCR[5:4]: Transmit FIFO Trigger Select
(’00’ = default, TX trigger level = 1)
These 2 bits set the trigger level for the transmit FIFO. The UART will issue a transmit interrupt when the
number of characters in the FIFO falls below the selected trigger level, or when it gets empty in case that the
FIFO did not get filled over the trigger level on last re-load. Table 8 below shows the selections. EFR bit-4 must
be set to ‘1’ before these bits can be accessed.
FCR[7:6]: Receive FIFO Trigger Select
(’00’ = default, RX trigger level =1)
These 2 bits are used to set the trigger level for the receive FIFO. The UART will issue a receive interrupt when
the number of the characters in the FIFO crosses the trigger level. Table 8 shows the selections.
4.7
Line Control Register (LCR) - Read/Write
The Line Control Register is used to specify the asynchronous data communication format. The word or
character length, the number of stop bits, and the parity are selected by writing the appropriate bits in this
register.
LCR[1:0]: TX and RX Word Length Select
These two bits specify the word length to be transmitted or received.
TABLE 8: TRANSMIT AND RECEIVE FIFO TRIGGER LEVEL SELECTION
FCR
BIT-7
FCR
BIT-6
FCR
BIT-5
FCR
BIT
-4
RECEIVE
TRIGGER LEVEL
TRANSMIT
TRIGGER LEVEL
COMPATIBILITY
0
1
0
1
0
1
1 (default)
4
8
14
16C580 and 16L580 compati-
ble.
0
1
0
1
0
1
1 (default)
4
8
14
16C550, 16C580, 16L580,
16C554, 16C2550 and 16C2552
compatible
BIT-1
BIT-0
WORD LENGTH
0
5 (default)
0
1
6
1
0
7
1
8
相關PDF資料
PDF描述
XR16M570IL24TR-F IC UART FIFO 16B 24QFN
ATMEGA324A-AUR IC MCU AVR 32K 20MHZ 44TQFP
ATMEGA324A-MUR IC MCU AVR 32K 20MHZ 44VQFN
MCP2200T-I/SO IC USB 2.0 - UART 20SOIC
MCP2200T-I/SS IC USB 2.0 - UART 20SSOP
相關代理商/技術參數
參數描述
XR16L580 制造商:EXAR 制造商全稱:EXAR 功能描述:SMALLEST 2.25V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE
XR16L580_07 制造商:EXAR 制造商全稱:EXAR 功能描述:SMALLEST 2.25V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE
XR16L580IL 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L580IL-0A-EVB 功能描述:UART 接口集成電路 Supports L580 32 pin QFN, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L580IL-0B-EVB 功能描述:UART 接口集成電路 Supports L580 32 pin QFN, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*