- 您現在的位置：買賣IC網 > PDF目錄376454 > XR16L78464-TQFP (Exar Corporation) HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART PDF資料下載
參數資料
| 型號： | XR16L78464-TQFP |
| 廠商： | Exar Corporation |
| 英文描述： | HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART |
| 中文描述： | 高性能2.97V至5.5V UART的四 |
| 文件頁數： | 30/52頁 |
| 文件大?。?/td> | 625K |
| 代理商： | XR16L78464-TQFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
XR16L784
HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART
á
REV. 1.2.0
30
ISR[7:6]: FIFO Enable Status
These bits are set to a logic 0 when the FIFOs are disabled. They are set to a logic 1 when the FIFOs are
enabled.
4.5
FIFO Control Register (FCR) - Write Only
This register is used to enable the FIFOs, clear the FIFOs, set the transmit/receive FIFO trigger levels, and
select the DMA mode. The DMA, and FIFO modes are defined as follows:
FCR[0]: TX and RX FIFO Enable
Logic 0 = Disable the transmit and receive FIFO (default).
Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are
written or they will not be programmed.
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is active.
Logic 0 = No receive
FIFO
reset (default).
Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is active.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[3]: DMA Mode Select
This bit has no effect since TXRDY and RXRDY pins are not available in this device. It is provided for legacy
software.
Logic 0 = Set DMA to mode 0 (default).
Logic 1 = Set DMA to mode 1.
FCR[5:4]: Transmit FIFO Trigger Select
(logic 0 = default, TX trigger level = one)
The FCTR Bits 6-7 are associated with these 2 bits by selecting one of the four tables. The 4 user selectable
trigger levels in 4 tables are supported for compatibility reasons. These 2 bits set the trigger level for the
transmit FIFO interrupt. The UART will issue a transmit interrupt when the number of characters in the FIFO
falls below the selected trigger level, or when it gets empty in case that the FIFO did not get filled over the
trigger level on last re-load.
Table 14
below shows the selections.
FCR[7:6]: Receive FIFO Trigger Select
(logic 0 = default, RX trigger level =1)
The FCTR Bits 5-4 are associated with these 2 bits. These 2 bits are used to set the trigger level for the receive
FIFO. The UART will issue a receive interrupt when the number of the characters in the FIFO crosses the
trigger level.
Table 14
shows the complete selections. Note that the receiver and the transmitter cannot use
different trigger tables. Whichever selection is made last applies to both the RX and TX side.
相關PDF資料 |
PDF描述 |
|---|---|
| XR16L784CV | HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART |
| XR16L784IV | HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART |
| XR16L788 | HIGH PERFORMANCE OCTAL UART |
| XR16L788CQ | HIGH PERFORMANCE OCTAL UART |
| XR16L788IQ | HIGH PERFORMANCE OCTAL UART |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16L784CV | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART |
| XR16L784CV-0A-EVB | 功能描述:UART 接口集成電路 Supports L784 64 ld TQFP, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L784CV-0B-EVB | 功能描述:UART 接口集成電路 Supports L784 64 ld TQFP, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L784CV-F | 功能描述:UART 接口集成電路 2.97V-5.5V 64B FIFO temp 0C to 70C RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L784CVTR-F | 功能描述:UART 接口集成電路 3.3V QUAD UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。