參數資料
型號： XR16L788IQ-F
廠商： Exar Corporation
文件頁數： 8/54頁
文件大?。?/td> 0K
描述： IC UART 64B 3.3V OCTAL 100QFP
標準包裝： 66
特點： *
通道數： 8
FIFO's： 64 字節
規程： RS485
電源電壓： 2.97 V ~ 5.5 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
安裝類型： 表面貼裝
封裝/外殼： 100-BQFP
供應商設備封裝： 100-QFP（14x20）
包裝： 托盤
其它名稱： 1016-1284
XR16L788
16
HIGH PERFORMANCE 2.97V TO 5.5V OCTAL UART
REV. 1.2.3
2.11
Auto Xon/Xoff (Software) Flow Control
When software flow control is enabled (See Table 18), the 788 compares one or two sequential receive data
characters with the programmed Xon or Xoff-1,2 character value(s). If receive character(s) (RX) match the
programmed values, the 788 will halt transmission (TX) as soon as the current character has completed
transmission. When a match occurs, the Xoff (if enabled via IER bit-5) flag will be set and the interrupt output
pin will be activated. Following a suspension due to a match of the Xoff character, the 788 will monitor the
receive data stream for a match to the Xon-1,2 character. If a match is found, the 788 will resume operation
and clear the flags (ISR bit-4).
Reset initially sets the contents of the Xon/Xoff 8-bit flow control registers to a logic 0. Following reset, any
desired Xon/Xoff value can be used for software flow control. Different conditions can be set to detect Xon/Xoff
characters (See Table 18) and suspend/resume transmissions. When double 8-bit Xon/Xoff characters are
selected, the 788 compares two consecutive receive characters with two software flow control 8-bit values
(Xon1, Xon2, Xoff1, Xoff2) and controls TX transmissions accordingly. Under the above described flow control
mechanisms, flow control characters are not placed (stacked) in the user accessible RX data buffer or FIFO.
In the event that the receive buffer is overfilling and flow control needs to be executed, the 788 automatically
sends an Xoff message (when enabled) via the serial TX output to the remote modem. The 788 sends the Xoff-
1,2 characters two character times (= time taken to send two characters at the programmed baud rate) after
the receive FIFO crosses the programmed trigger level (for all trigger tables A-D). To clear this condition, the
788 will transmit the programmed Xon-1,2 characters as soon as receive FIFO is less than one trigger level
below the programmed trigger level (for Trigger Tables A, B, and C) or when receive FIFO is less than the
trigger level minus the hysteresis value (for Trigger Table D). This hysteresis value is the same as the Auto
RTS/DTR Hysteresis value in Table 17. Table 6 below explains this when Trigger Table-B (See Table 14) is
selected.
* After the trigger level is reached, an xoff character is sent after a short span of time (= time required to send 2
characters); for example, after 2.083ms has elapsed for 9600 baud and 10-bit word length setting.
2.12
Special Character Detect
A special character detect feature is provided to detect an 8-bit character when bit-5 is set in the Enhanced
Feature Register (EFR). When this character (Xoff2) is detected, it will be placed in the FIFO along with normal
incoming RX data.
The 788 compares each incoming receive character with Xoff-2 data. If a match exists, the received data will
be transferred to FIFO and ISR bit-4 will be set to indicate detection of special character. Although the Internal
Register Table shows Xon, Xoff Registers with eight bits of character information, the actual number of bits is
dependent on the programmed word length. Line Control Register (LCR) bits 0-1 defines the number of
character bits, i.e., either 5 bits, 6 bits, 7 bits, or 8 bits. The word length selected by LCR bits 0-1 also
determines the number of bits that will be used for the special character comparison. Bit-0 in the Xon, Xoff
Registers corresponds with the LSB bit for the receive character.
2.13
Auto RS485 Half-duplex Control
The auto RS485 half-duplex direction control changes the behavior of the transmitter when enabled by FCTR
bit-5. It asserts RTS# or DTR# (LOW) after a specified delay indicated in MSR[7:4] following the last stop bit of
the last character that has been transmitted. This helps in turning around the transceiver to receive the remote
station’s response. The delay optimizes the time needed for the last transmission to reach the farthest station
on a long cable network before switching off the line driver. This delay prevents undesirable line signal
TABLE 6: AUTO XON/XOFF (SOFTWARE) FLOW CONTROL
RX TRIGGER LEVEL
INT PIN ACTIVATION
XOFF CHARACTER(S) SENT
(CHARACTERS IN RX FIFO)
XON CHARACTER(S) SENT
(CHARACTERS IN RX FIFO)
8
8*
0
16
16*
8
24
24*
16
28
28*
24
相關PDF資料
PDF描述
XR16M2550IL32-F IC UART FIFO 16B 1.8V DUAL 32QFN
XR16M2551IL32-F IC UART FIFO 16B DUAL 32QFN
XR16M2650IM48-F IC UART FIFO 32B DUAL 48TQFP
XR16M2651IM48-F IC UART FIFO 32B DUAL 48TQFP
XR16M2750IM48-F IC UART FIFO 64B DUAL 48TQFP
相關代理商/技術參數
參數描述
XR16L788IQTR-F 功能描述:UART 接口集成電路 3.3V OCTAL UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16M2550 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE LOW VOLTAGE DUART WITH 16-BYTE FIFO
XR16M2550IL-0B-EB 功能描述:UART 接口集成電路 Supports M2550 32pin QFN, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16M2550IL32 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
XR16M2550IL32-F 功能描述:UART 接口集成電路 1.62V-3.63V 16B FIFO temp -45 to 85C RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*