- 您現在的位置：買賣IC網 > PDF目錄16507 > XR16M554IV80-0A-EB (Exar Corporation)EVAL BOARD FOR XR16M554-A 80LQFP PDF資料下載
參數資料
| 型號： | XR16M554IV80-0A-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 8/46頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR XR16M554-A 80LQFP |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
XR16M554/554D
16
1.62V TO 3.63V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.0
2.10
Receiver
The receiver section contains an 8-bit Receive Shift Register (RSR) and 16 bytes of FIFO which includes a
byte-wide Receive Holding Register (RHR). The RSR uses the 16X clock for timing. It verifies and validates
every bit on the incoming character in the middle of each data bit. On the falling edge of a start or false start bit,
an internal receiver counter starts counting at the 16X clock rate. After 8 clocks the start bit period should be at
the center of the start bit. At this time the start bit is sampled and if it is still LOW it is validated. Evaluating the
start bit in this manner prevents the receiver from assembling a false character. The rest of the data bits and
stop bits are sampled and validated in this same manner to prevent false framing. If there were any error(s),
they are reported in the LSR register bits 2-4. Upon unloading the receive data byte from RHR, the receive
FIFO pointer is bumped and the error tags are immediately updated to reflect the status of the data byte in
RHR register. RHR can generate a receive data ready interrupt upon receiving a character or delay until it
reaches the FIFO trigger level. Furthermore, data delivery to the host is guaranteed by a receive data ready
time-out interrupt when data is not received for 4 word lengths as defined by LCR[1:0] plus 12 bits time. This is
equivalent to 3.7-4.6 character times. The RHR interrupt is enabled by IER bit-0. See Figure 9 and Figure 10
below.
2.10.1
Receive Holding Register (RHR) - Read-Only
The Receive Holding Register is an 8-bit register that holds a receive data byte from the Receive Shift
Register. It provides the receive data interface to the host processor. The RHR register is part of the receive
FIFO of 16 bytes by 11-bit wide, the 3 extra bits are for the 3 error tags to be reported in LSR register. When
the FIFO is enabled by FCR bit-0, the RHR contains the first data character received by the FIFO. After the
RHR is read, the next character byte is loaded into the RHR and the errors associated with the current data
byte are immediately updated in the LSR bits 2-4.
FIGURE 9. RECEIVER OPERATION IN NON-FIFO MODE
Receive Data Shift
Register (RSR)
Receive
Data Byte
and Errors
RHR Interrupt (ISR bit-2)
Receive Data
Holding Register
(RHR)
RXFIFO1
16X Clock
Receive Data Characters
Data Bit
Validation
Error
Tags in
LSR bits
4:2
相關PDF資料 |
PDF描述 |
|---|---|
| XR16M554IV-0A-EVB | EVAL BOARD FOR XR16M554-A 64LQFP |
| H3KKH-1006M | IDC CABLE - HPK10H/AE10M/HPK10H |
| EBM28DTMH-S189 | CONN EDGECARD 56POS R/A .156 SLD |
| VI-J52-EX | CONVERTER MOD DC/DC 15V 75W |
| IMC0402ER2N2S | INDUCTOR 2.2NH 0402 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16M554IV80-0B-EB | 功能描述:界面開發工具 Eval Board for XR16M554IV80-0B RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR16M554IV80-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16M564 | 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO |
| XR16M564D | 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO |
| XR16M564DIV-0A-EVB | 功能描述:界面開發工具 Eval Board for XR16M564DIV-0A RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。