參數資料
型號: XR16M570IL24-0B-EB
廠商: Exar Corporation
文件頁數: 25/50頁
文件大?。?/td> 0K
描述: EVAL BOARD FOR XR16M570-B 24QFN
標準包裝: 1
系列: *
XR16M570
31
REV. 1.0.1
1.62V TO 3.63V HIGH PERFORMANCE UART WITH 16-BYTE FIFO
LCR[4]: TX and RX Parity Select
If the parity bit is enabled with LCR bit-3 set to a logic 1, LCR BIT-4 selects the even or odd parity format.
Logic 0 = ODD Parity is generated by forcing an odd number of logic 1’s in the transmitted character. The
receiver must be programmed to check the same format (default).
Logic 1 = EVEN Parity is generated by forcing an even number of logic 1’s in the transmitted character. The
receiver must be programmed to check the same format.
LCR[5]: TX and RX Parity Select
If the parity bit is enabled, LCR BIT-5 selects the forced parity format.
LCR BIT-5 = logic 0, parity is not forced (default).
LCR BIT-5 = logic 1 and LCR BIT-4 = logic 0, parity bit is forced to a logical 1 for the transmit and receive
data.
LCR BIT-5 = logic 1 and LCR BIT-4 = logic 1, parity bit is forced to a logical 0 for the transmit and receive
data.
LCR[6]: Transmit Break Enable
When enabled, the Break control bit causes a break condition to be transmitted (the TX output is forced to a
“space’, logic 0, state). This condition remains, until disabled by setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition. (default)
Logic 1 = Forces the transmitter output (TX) to a “space”, logic 0, for alerting the remote receiver of a line
break condition.
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL/DLM/DLD) enable.
Logic 0 = Data registers are selected. (default)
Logic 1 = Divisor latch registers are selected.
4.7
Modem Control Register (MCR) or General Purpose Outputs Control - Read/Write
The MCR register is used for controlling the serial/modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Output
The DTR# pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
Logic 0 = Force DTR# output HIGH (default).
Logic 1 = Force DTR# output LOW.
TABLE 10: PARITY SELECTION
LCR BIT-5 LCR BIT-4 LCR BIT-3
PARITY SELECTION
XX
0
No parity
00
1
Odd parity
01
1
Even parity
1
0
1
Force parity to mark, HIGH
1
Forced parity to space, LOW
相關PDF資料
PDF描述
SPD73R-103M INDUCTOR PWR SHIELDED 10UH SMD
1906015-8 CA 2.0MM OFNR 50/125,LC SEC GRN
CM252016-2R2KL INDUCTOR CHIP 2.2UH 2520 SMD
6278027-1 C/A ST/MT-RJ, MM 1M1
ECM18DSXH CONN EDGECARD 36POS DIP .156 SLD
相關代理商/技術參數
參數描述
XR16M570IL24-0C-EB 功能描述:界面開發工具 Eval Board for XR16M570IL24 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR16M570IL24-F 功能描述:UART 接口集成電路 1.8 HIGH PERFORMANCE UART W/16 RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16M570IL24TR-F 功能描述:UART 接口集成電路 1.8 HIGH PERFORMANCE UART W/16 RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16M570IL32 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE UART WITH 16-BYTE FIFO
XR16M570IL32-0A-EB 功能描述:界面開發工具 Eval Board for XR16M570IL32 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V