- 您現在的位置：買賣IC網 > PDF目錄3767 > XR16M581IL24-F (Exar Corporation)IC UART FIFO 16B 24QFN PDF資料下載
參數資料
| 型號： | XR16M581IL24-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 11/51頁 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 16B 24QFN |
| 標準包裝： | 490 |
| 特點： | * |
| 通道數： | 1，UART |
| FIFO's： | 16 字節 |
| 規程： | RS232，RS422，RS485 |
| 電源電壓： | 1.62 V ~ 3.63 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 24-QFN 裸露焊盤（4x4） |
| 包裝： | 托盤 |
| 其它名稱： | 1016-1456 XR16M581IL24-F-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
XR16M581
19
REV. 1.0.1
1.62V TO 3.63V UART WITH 16-BYTE FIFO AND VLIO INTERFACE
interrupt and place the address byte in the RX FIFO. The software then examines the byte and enables the
receiver if the address matches its slave address, otherwise, it does not enable the receiver.
If the receiver has been enabled, the receiver will receive the subsequent data. If an address byte is received,
it will generate an LSR interrupt. The software again examines the byte and if the address matches its slave
address, it does not have to do anything. If the address does not match its slave address, then the receiver
should be disabled.
2.15.1
Auto Address Detection
Auto address detection mode is enabled when MSR[6] = 1 (requires EFR[4] = 1) and EFR bit-5 = 1. The
desired slave address will need to be written into the XOFF2 register. The receiver will try to detect an address
byte that matches the porgrammed character in the XOFF2 register. If the received byte is a data byte or an
address byte that does not match the programmed character in the XOFF2 register, the receiver will discard
these data.
Upon receiving an address byte that matches the XOFF2 character, the receiver will be
automatically enabled if not already enabled, and the address character is pushed into the RX FIFO along with
the parity bit (in place of the parity error bit). The receiver also generates an LSR interrupt. The receiver will
then receive the subsequent data. If another address byte is received and this address does not match the
programmed XOFF2 character, then the receiver will automatically be disabled and the address byte is
ignored. If the address byte matches XOFF2, the receiver will put this byte in the RX FIFO along with the parity
bit in the parity error bit.
2.16
Infrared Mode
The M581 UART includes the infrared encoder and decoder compatible to the IrDA (Infrared Data Association)
version 1.0 and 1.1. The IrDA 1.0 standard that stipulates the infrared encoder sends out a 3/16 of a bit wide
HIGH-pulse for each “0” bit in the transmit data stream with a data rate up to 115.2 Kbps. For the IrDA 1.1
standard, the infrared encoder sends out a 1/4 of a bit time wide HIGH-pulse for each "0" bit in the transmit
data stream with a data rate up to 1.152 Mbps. This signal encoding reduces the on-time of the infrared LED,
hence reduces the power consumption. See Figure 13 below.
The infrared encoder and decoder are enabled by setting MCR register bit-6 to a ‘1’. With this bit enabled, the
infrared encoder and decoder is compatible to the IrDA 1.0 standard. For the infrared encoder and decoder to
be compatible to the IrDA 1.1 standard, MSR bit-7 will also need to be set to a ’1’ when EFR bit-4 is set to ’1’.
Likewise, the RX input assumes an idle level of logic zero from a reset and power up, see Figure 13.
Typically, the wireless infrared decoder receives the input pulse from the infrared sensing diode on the RX pin.
Each time it senses a light pulse, it returns a logic 1 to the data bit stream.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX7312AWG+ | IC I/O EXPANDER I2C 16B 24SOIC |
| XR16M581IB25-F | IC UART FIFO 16B 25BGA |
| ATMEGA88V-10MUR | MCU AVR 8K FLASH 10MHZ 32QFN |
| DS4550E+T&R | IC I/O EXPANDER I2C 9B 20TSSOP |
| MAX7318AAG+ | IC I/O EXPANDER I2C 16B 24SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16M581IL32 | 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V UART WITH 16-BYTE FIFO AND VLIO INTERFACE |
| XR16M581IL32-0C-EB | 功能描述:界面開發工具 Eval Board for XR16M581IL32 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR16M581IL32-F | 功能描述:UART 接口集成電路 1.62-3.63V; 16-Byte FIFO & VLIO; UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16M598 | 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE OCTAL UART WITH 16-BYTE FIFO |
| XR16M598IQ100 | 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE OCTAL UART WITH 16-BYTE FIFO |
發布緊急采購，3分鐘左右您將得到回復。