參數資料
型號： XR16M680IL32-F
廠商： Exar Corporation
文件頁數： 28/57頁
文件大?。?/td> 0K
描述： IC UART FIFO 32B 32QFN
標準包裝： 490
特點： *
通道數： 1，UART
FIFO's： 32 字節
規程： RS232，RS422，RS485
電源電壓： 1.62 V ~ 3.63 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 32-VFQFN 裸露焊盤
供應商設備封裝： 32-QFN 裸露焊盤（5x5）
包裝： 托盤
XR16M680
34
1.62V TO 3.63V HIGH PERFORMANCE UART WITH 32-BYTE FIFO
REV. 1.0.0
LCR[6]: Transmit Break Enable
When enabled, the Break control bit causes a break condition to be transmitted (the TX output is forced to a
“space’, logic 0, state). This condition remains, until disabled by setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition. (default)
Logic 1 = Forces the transmitter output (TX) to a “space”, logic 0, for alerting the remote receiver of a line
break condition.
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL/DLM/DLD) enable.
Logic 0 = Data registers are selected. (default)
Logic 1 = Divisor latch registers are selected.
4.7
Modem Control Register (MCR) or General Purpose Outputs Control - Read/Write
The MCR register is used for controlling the serial/modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Output
The DTR# pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
Logic 0 = Force DTR# output HIGH (default).
Logic 1 = Force DTR# output LOW.
MCR[1]: RTS# Output
The RTS# pin is a modem control output and may be used for automatic hardware flow control by enabled by
EFR bit-6. If the modem interface is not used, this output may be used as a general purpose output.
Logic 0 = Force RTS# output HIGH (default).
Logic 1 = Force RTS# output LOW. It is required to start Auto RTS Flow Control.
MCR[2]: Reserved
OP1# is not available as an output pin on the M680. But it is available for use during Internal Loopback Mode.
In the Loopback Mode, this bit is used to write the state of the modem RI# interface signal.
MCR[3]: INT Output Enable
Enable or disable INT outputs to become active or in three-state. This bit is also used to control the OP2#
signal during internal loopback mode.
Logic 0 = INT output disabled (three state) in the 16 mode (default). During internal loopback mode, OP2# is
HIGH.
Logic 1 = INT output enabled (active) in the 16 mode. During internal loopback mode, OP2# is LOW.
TABLE 11: INT OUTPUT MODES
MCR
BIT-3
INT OUTPUT IN 16 MODE
0
Three-State
1
Active
相關PDF資料
PDF描述
XR16M580IL32-F IC UART FIFO 16B 32QFN
XR16M670IL24-F IC UART FIFO 32B 24QFN
ST16C450CJ44TR-F IC UART SINGLE 44PLCC
XR16M780IB25-F IC UART FIFO 64B 25BGA
XR16M770IB25-F IC UART FIFO 64B 25BGA
相關代理商/技術參數
參數描述
XR16M680IM48 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE UART WITH 32-BYTE FIFO
XR16M680IM48-0A-EB 功能描述:界面開發工具 Eval Board for XR16M680IM48 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR16M680IM48-0C-EB 功能描述:界面開發工具 Eval Board for XR16M680IM48 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR16M680IM48-F 功能描述:UART 接口集成電路 1.8 HIGH PERFORMANCE UART W/32 RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16M681 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V UART WITH 32-BYTE FIFO AND VLIO INTERFACE
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*