- 您現在的位置：買賣IC網 > PDF目錄3762 > XR16M780IL32-F (Exar Corporation)IC UART FIFO 64B 32QFN PDF資料下載
參數資料
| 型號： | XR16M780IL32-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 13/58頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO 64B 32QFN |
| 標準包裝： | 490 |
| 特點： | * |
| 通道數： | 1，UART |
| FIFO's： | 64 字節 |
| 規程： | RS232，RS422，RS485 |
| 電源電壓： | 1.62 V ~ 3.63 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-QFN 裸露焊盤（5x5） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
XR16M780
20
1.62V TO 3.63V HIGH PERFORMANCE UART WITH 64-BYTE FIFO
REV. 1.0.0
2.13
Auto Xon/Xoff (Software) Flow Control
When software flow control is enabled (See Table 17), the M780 compares one or two sequential receive data
characters with the programmed Xon or Xoff-1,2 character value(s). If receive character(s) (RX) match the
programmed values, the M780 will halt transmission (TX) as soon as the current character has completed
transmission. When a match occurs, the Xoff (if enabled via IER bit-5) flag will be set and the interrupt output
pin will be activated. Following a suspension due to a match of the Xoff character, the M780 will monitor the
receive data stream for a match to the Xon-1,2 character. If a match is found, the M780 will resume operation
and clear the flags (ISR bit-4).
Reset initially sets the contents of the Xon/Xoff 8-bit flow control registers to a logic 0. Following reset the user
can write any Xon/Xoff value desired for software flow control. Different conditions can be set to detect Xon/
Xoff characters (See Table 17) and suspend/resume transmissions. When double 8-bit Xon/Xoff characters
are selected, the M780 compares two consecutive receive characters with two software flow control 8-bit
values (Xon1, Xon2, Xoff1, Xoff2) and controls TX transmissions accordingly. Under the above described flow
control mechanisms, flow control characters are not placed (stacked) in the user accessible RX data buffer or
FIFO.
In the event that the receive buffer is overfilling and flow control needs to be executed, the M780 automatically
sends an Xoff message (when enabled) via the serial TX output to the remote modem. The M780 sends the
Xoff-1,2 characters two-character-times (= time taken to send two characters at the programmed baud rate)
after the receive FIFO crosses the programmed trigger level. To clear this condition, the M780 will transmit the
programmed Xon-1,2 characters as soon as receive FIFO is less than one trigger level below the programmed
trigger level. Table 5 below explains this.
* After the trigger level is reached, an xoff character is sent after a short span of time (= time required to send 2 characters);
for example, after 2.083ms has elapsed for 9600 baud and 10-bit word length setting.
2.14
Special Character Detect
A special character detect feature is provided to detect an 8-bit character when bit-5 is set in the Enhanced
Feature Register (EFR). When this character (Xoff2) is detected, it will be placed in the FIFO along with normal
incoming RX data.
The M780 compares each incoming receive character with Xoff-2 data. If a match exists, the received data will
be transferred to the RX FIFO and ISR bit-4 will be set to indicate detection of special character. Although the
Internal Register Table shows Xon, Xoff Registers with eight bits of character information, the actual number of
bits is dependent on the programmed word length. Line Control Register (LCR) bits 0-1 defines the number of
character bits, i.e., either 5 bits, 6 bits, 7 bits, or 8 bits. The word length selected by LCR bits 0-1 also
determines the number of bits that will be used for the special character comparison. Bit-0 in the Xon, Xoff
Registers corresponds with the LSB bit for the receive character.
2.15
Normal Multidrop Mode
Normal multidrop mode is enabled when MSR[6] = 1 (requires EFR[4] = 1) and EFR[5] = 0 (Special Character
Detect disabled). The receiver is set to Force Parity 0 (LCR[5:3] = ’111’) in order to detect address bytes.
With the receiver initially disabled, it ignores all the data bytes (parity bit = 0) until an address byte is received
(parity bit = 1). This address byte will cause the UART to set the parity error. The UART will generate an LSR
TABLE 5: AUTO XON/XOFF (SOFTWARE) FLOW CONTROL
RX TRIGGER LEVEL
INT PIN ACTIVATION
XOFF CHARACTER(S) SENT
(CHARACTERS IN RX FIFO)
XON CHARACTER(S) SENT
(CHARACTERS IN RX FIFO)
8
8*
0
16
16*
8
56
56*
16
60
60*
56
相關PDF資料 |
PDF描述 |
|---|---|
| XR68M752IL32TR-F | IC UART FIFO 64B DUAL 32QFN |
| ATMEGA168-15AT | MCU AVR 16K FLASH 15MHZ 32-TQFP |
| ST16C450CQ48TR-F | IC UART SINGLE 48TQFP |
| ST16C450IJ44TR-F | IC UART SINGLE 44PLCC |
| XR16M770IL24-F | IC UART FIFO 64B 24QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16M780IM48 | 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE UART WITH 64-BYTE FIFO |
| XR16M780IM48-0A-EB | 功能描述:界面開發工具 Eval Board for XR16M780IM48 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR16M780IM48-0C-EB | 功能描述:界面開發工具 Eval Board for XR16M780IM48 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR16M780IM48-F | 功能描述:UART 接口集成電路 1.8 HIGH PERFORMANCE UART W/64 RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16M781 | 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V UART WITH 64-BYTE FIFO AND VLIO INTERFACE |
發布緊急采購，3分鐘左右您將得到回復。