- 您現在的位置：買賣IC網 > PDF目錄16491 > XR16V564IV80-0A-EB (Exar Corporation)EVAL BOARD FOR XR16V564 80LQFP PDF資料下載
參數資料
| 型號： | XR16V564IV80-0A-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 27/54頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR XR16V564 80LQFP |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
XR16V564/564D
33
REV. 1.0.4
2.25V TO 3.6V QUAD UART WITH 32-BYTE FIFO
MCR[3]: INT Output Enable
Enable or disable INT outputs to become active or in three-state. This function is associated with the INTSEL
input, see below table for details. This bit is also used to control the OP2# signal during internal loopback
mode. INTSEL pin must be LOW during 68 mode.
Logic 0 = INT (A-D) outputs disabled (three state) in the 16 mode (default). During internal loopback mode,
OP2# is HIGH.
Logic 1 = INT (A-D) outputs enabled (active) in the 16 mode. During internal loopback mode, OP2# is LOW.
TABLE 14: INT OUTPUT MODES
PIN
BIT-3
INT A-D OUTPUTS IN 16 MODE
0
Three-State
0
1
Active
1
X
Active
MCR[4]: Internal Loopback Enable
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and Figure 13.
MCR[5]: Xon-Any Enable (requires EFR bit-4 = 1)
Logic 0 = Disable Xon-Any function (for 16C550 compatibility, default).
Logic 1 = Enable Xon-Any function. In this mode, any RX character received will resume transmit operation.
The RX character will be loaded into the RX FIFO , unless the RX character is an Xon or Xoff character and
the V564 is programmed to use the Xon/Xoff flow control.
MCR[6]: Infrared Encoder/Decoder Enable (requires EFR bit-4 = 1)
Logic 0 = Enable the standard modem receive and transmit input/output interface (default).
Logic 1 = Enable infrared IrDA receive and transmit inputs/outputs. The TX/RX output/input are routed to the
infrared encoder/decoder. The data input and output levels conform to the IrDA infrared interface
requirement. The RX FIFO may need to be flushed upon enable. While in this mode, the infrared TX output
will be LOW during idle data conditions.
MCR[7]: Clock Prescaler Select (requires EFR bit-4 = 1)
Logic 0 = Divide by one. The input clock from the crystal or external clock is fed directly to the Programmable
Baud Rate Generator without further modification, i.e., divide by one (default).
Logic 1 = Divide by four. The prescaler divides the input clock from the crystal or external clock by four and
feeds it to the Programmable Baud Rate Generator, hence, data rates become one forth.
INTSEL
MCR
相關PDF資料 |
PDF描述 |
|---|---|
| ECM18DRXH | CONN EDGECARD 36POS DIP .156 SLD |
| A3932SEQ | IC CTRLR MOSFET 3PH 32-PLCC |
| RPP30-4824SW | CONV DC/DC 30W 18-75VIN 24VOUT |
| 6374645-4 | C/A MTRJ TO LC SM OFNR 4M1 |
| XC61CN1802MR-G | IC SUPERVISOR 1.8V SOT23-3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16V564IV80-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16V564IV80TR-F | 制造商:Exar Corporation 功能描述:UART 4-CH 32Byte FIFO 2.5V/3.3V 80-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR16V564IV80TR-F |
| XR16V564IV-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16V564IVTR-F | 制造商:Exar Corporation 功能描述:UART 4-CH 32Byte FIFO 2.5V/3.3V 64-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR16V564IVTR-F |
| XR16V598 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 16-BYTE FIFO |
發布緊急采購，3分鐘左右您將得到回復。