參數資料
型號: XR17C152CM-F
廠商: Exar Corporation
文件頁數: 22/62頁
文件大小: 0K
描述: IC UART PCI BUS DUAL 100TQFP
標準包裝: 90
特點: *
通道數: 2,DUART
FIFO's: 64 字節
規程: RS485
電源電壓: 5V
帶自動流量控制功能:
帶IrDA 編碼器/解碼器:
帶故障啟動位檢測功能:
帶調制解調器控制功能:
安裝類型: 表面貼裝
封裝/外殼: 100-TQFP
供應商設備封裝: 100-TQFP(14x14)
包裝: 托盤
á
XR17C152
REV. 1.2.0
5V PCI BUS DUAL UART
29
Two interrupts associated with auto RTS/CTS and DTR/DSR flow control have been added to give indication
when RTS#/DTR# pin or CTS#/DSR# pin are de-asserted during operation. These interrupts are enabled by:
Setting EFR bit-4 =1 to enable the shaded register bits
Setting IER bit-7 will enable the CTS#/DSR# interrupt when these pins are de-asserted. The selection of
CTS# or DSR# is selected via MCR bit-2. See Table 10 above for complete details.
Setting IER bit-6 will enable the RTS#/DTR# interrupt when these pins are de-asserted. The selection of
RTS# or DTR# is selected via MCR bit-2. See Table 10 above for complete details.
Automatic hardware flow control is selected by setting bits 6 (RTS) and 7 (CTS) of the EFR register to logic 1.
If CTS# pin transitions from LOW to HIGH indicating a flow control request, ISR bit-5 will be set to logic 1, (if
enabled via IER bit 6-7), and the UART will suspend TX transmissions as soon as the stop bit of the character
in process is shifted out. Transmission is resumed after the CTS# input returns LOW, indicating more data may
be sent.
FIGURE 14. AUTO RTS/DTR AND CTS/DSR FLOW CONTROL OPERATION
The local UART (UARTA) starts data transfer by asserting -RTSA# (1). RTSA# is normally connected to CTSB# (2) of
remote UART (UARTB). CTSB# allows its transmitter to send data (3). TXB data arrives and fills UARTA receive FIFO
(4). When RXA data fills up to its receive FIFO trigger level, UARTA activates its RXA data ready interrupt (5) and con-
tinues to receive and put data into its FIFO. If interrupt service latency is long and data is not being unloaded, UARTA
monitors its receive data fill level to match the upper threshold of RTS delay and de-assert RTSA# (6). CTSB# follows
(7) and request UARTB transmitter to suspend data transfer. UARTB stops or finishes sending the data bits in its trans-
mit shift register (8). When receive FIFO data in UARTA is unloaded to match the lower threshold of RTS delay (9),
UARTA re-asserts RTSA# (10), CTSB# recognizes the change (11) and restarts its transmitter and data flow again until
next receive FIFO trigger (12). This same event applies to the reverse direction when UARTA sends data to UARTB
with RTSB# and CTSA# controlling the data flow.
RTSA#
CTSB#
RXA
TXB
Transmitter
Receiver FIFO
Trigger Reached
Auto RTS
Trigger Level
Auto CTS
Monitor
RTSA#
TXB
RXA FIFO
CTSB#
Remote UART
UARTB
Local UART
UARTA
ON
OFF
ON
Suspend
Restart
RTS High
Threshold
Data Starts
ON
OFF
ON
Assert RTS# to Begin
Transmission
1
2
3
4
5
6
7
Receive
Data
RTS Low
Threshold
9
10
11
Receiver FIFO
Trigger Reached
Auto RTS
Trigger Level
Transmitter
Auto CTS
Monitor
RTSB#
CTSA#
RXB
TXA
INTA
(RXA FIFO
Interrupt)
RX FIFO
Trigger Level
RX FIFO
Trigger Level
8
12
RTSCTS1
相關PDF資料
PDF描述
VE-B73-IW-F4 CONVERTER MOD DC/DC 24V 100W
XR16L784CVTR-F IC UART FIFO 64B QUAD 64LQFP
VE-B73-IW-F2 CONVERTER MOD DC/DC 24V 100W
XR16V654IQ-F IC UART FIFO 64B QUAD 100QFP
ATMEGA644A-AUR IC MCU AVR 64K FLASH 44TQFP
相關代理商/技術參數
參數描述
XR17C152IM 制造商:EXAR 制造商全稱:EXAR 功能描述:5V PCI BUS DUAL UART
XR17C152IM-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR17C154 制造商:EXAR 制造商全稱:EXAR 功能描述:5V PCI BUS QUAD UART
XR17C154_05 制造商:EXAR 制造商全稱:EXAR 功能描述:5V PCI BUS QUAD UART
XR17C154CV 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel