- 您現在的位置：買賣IC網 > PDF目錄376454 > XR17D152CM (EXAR CORP) UNIVERSAL (3.3V AND 5V) PCI BUS DUAL UART PDF資料下載
參數資料
| 型號： | XR17D152CM |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | UNIVERSAL (3.3V AND 5V) PCI BUS DUAL UART |
| 中文描述： | 2 CHANNEL(S), 6.25M bps, SERIAL COMM CONTROLLER, PQFP100 |
| 封裝： | 14 X 14 MM, 1 MM HEIGHT, TQFP-100 |
| 文件頁數： | 37/68頁 |
| 文件大小： | 772K |
| 代理商： | XR17D152CM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
á
REV. 1.2.0
XR17D152
UNIVERSAL (3.3V AND 5V) PCI BUS DUAL UART
37
IER[0]: RHR Interrupt Enable
The receive data ready interrupt will be issued when RHR has a data character in the non-FIFO mode or when
the receive FIFO has reached the programmed trigger level in the FIFO mode. A receive data timeout interrupt
will be issued in the FIFO mode when the receive FIFO has not reached the programmed trigger level and the
RX input has been idle for 4 character + 12 bit times.
Logic 0 = Disable the receive data ready interrupt (default).
Logic 1 = Enable the receiver data ready interrupt.
IER[1]: THR Interrupt Enable
When Auto RS485 mode operation is disabled (FCTR bit-5 = 0), this interrupt is associated with bit-5 in the
LSR register. An interrupt is issued whenever the THR becomes empty or when data in the FIFO falls below
the programmed trigger level. When Auto RS485 mode operation is enabled (FCTR bit-5 = 1), this interrupt is
associated with bit-6 in the LSR register. An interrupt is issued whenever the TX FIFO and the TSR becomes
empty.
Logic 0 = Disable Transmit Holding Register empty interrupt (default).
Logic 1 = Enable Transmit Holding Register empty interrupt.
IER[2]: Receive Line Status Interrupt Enable
Any of LSR register bits 1, 2, 3 or 4 will generate an LSR interrupt immediately when a character received by
the RX FIFO has an error.
Logic 0 = Disable the receiver line status interrupt (default).
Logic 1 = Enable the receiver line status interrupt.
IER[3]: Modem Status Interrupt Enable
Logic 0 = Disable the modem status register interrupt (default).
Logic 1 = Enable the modem status register interrupt.
IER[4]: Reserved
IER[5]: Xoff Interrupt Enable (requires EFR bit-4=1)
Logic 0 = Disable the software flow control, receive Xoff interrupt (default).
Logic 1 = Enable the software flow control, receive Xoff interrupt. See Software Flow Control section for
details.
IER[6]: RTS#/DTR# Output Interrupt Enable (requires EFR bit-4=1)
The RTS# or DTR# output is selected via MCR bit-2. See
Table 10
or MCR[2] for complete details.
Logic 0 = Disable the RTS#/DTR# interrupt (default).
Logic 1 = Enable the RTS#/DTR# interrupt. The UART issues an interrupt when the RTS#/DTR# pin makes a
transition.
IER[7]: CTS# Input Interrupt Enable (requires EFR bit-4=1)
The CTS# or DSR# input is selected via MCR bit-2. See
Table 10
or MCR[2] for complete details.
Logic 0 = Disable the CTS#/DSR# interrupt (default).
Logic 1 = Enable the CTS#/DSR# interrupt. The UART issues an interrupt when CTS# pin makes a transi-
tion.
5.8.5
Interrupt Status Register (ISR) - Read-Only
The UART provides multiple levels of prioritized interrupts to minimize external software interaction. The Inter-
rupt Status Register (ISR) provides the user with six interrupt status bits. Performing a read cycle on the ISR
will give the user the current highest pending interrupt level to be serviced with others queued up for next ser-
vice. No other interrupts are acknowledged until the pending interrupt is serviced. The Interrupt Source Table,
Table 13
, shows the data values (bit 0-5) for the six prioritized interrupt levels and the interrupt sources associ-
ated with each of these interrupt levels.
相關PDF資料 |
PDF描述 |
|---|---|
| XR17D152IM | UNIVERSAL (3.3V AND 5V) PCI BUS DUAL UART |
| XR17D158IV | UNIVERSAL (3.3V AND 5V) PCI BUS OCTAL UART |
| XR17D158 | UNIVERSAL (3.3V AND 5V) PCI BUS OCTAL UART |
| XR17D158CV | UNIVERSAL (3.3V AND 5V) PCI BUS OCTAL UART |
| XR17L152IM | CAP .068UF 400V PEN FILM 2825 5% |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR17D152CM-0A-EVB | 功能描述:界面開發工具 Supports D152 100 ld TQFP, PCI Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR17D152CM-F | 功能描述:UART 接口集成電路 3.3V-5V 64B FIFO temp 0C to 70C; UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR17D152CMTR-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR17D152IM | 制造商:EXAR 制造商全稱:EXAR 功能描述:UNIVERSAL (3.3V AND 5V) PCI BUS DUAL UART |
| XR17D152IM-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。