REV. 1.1.0 I2C/SPI UART WITH 64-BYTE FIFO LCR[5]: TX and RX Parity Select If the parity bit is enabled, LCR BIT-5 selects the forc" />
參數資料
型號： XR20M1170G24-0A-EB
廠商： Exar Corporation
文件頁數： 25/56頁
文件大小： 0K
描述： EVAL BOARD FOR XR20M1170 24TSSOP
標準包裝： 1
主要目的： 接口，UART
嵌入式： 否
已用 IC / 零件： XR20M1170
次要屬性： I²C & SPI 接口
已供物品： 板
其它名稱： 1016-1616
XR20M1170G24-0A-EB-ND
XR20M1170
31
REV. 1.1.0
I2C/SPI UART WITH 64-BYTE FIFO
LCR[5]: TX and RX Parity Select
If the parity bit is enabled, LCR BIT-5 selects the forced parity format.
LCR BIT-5 = logic 0, parity is not forced (default).
LCR BIT-5 = logic 1 and LCR BIT-4 = logic 0, parity bit is forced to a logical 1 for the transmit and receive
data.
LCR BIT-5 = logic 1 and LCR BIT-4 = logic 1, parity bit is forced to a logical 0 for the transmit and receive
data.
TABLE 11: PARITY SELECTION
LCR BIT-5 LCR BIT-4 LCR BIT-3
PARITY SELECTION
X
0
No parity
0
1
Odd parity
0
1
Even parity
1
0
1
Force parity to mark, “1”
1
Forced parity to space, “0”
LCR[6]: Transmit Break Enable
When enabled, the Break control bit causes a break condition to be transmitted (the TX output is forced to a
“space", LOW state). This condition remains, until disabled by setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition (default).
Logic 1 = Forces the transmitter output (TX) to a “space”, LOW, for alerting the remote receiver of a line
break condition.
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL, DLM and DLD) enable.
Logic 0 = Data registers are selected (default).
Logic 1 = Divisor latch registers are selected.
4.7
Modem Control Register (MCR) or General Purpose Outputs Control - Read/Write
The MCR register is used for controlling the serial/modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Output
The DTR# pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
Logic 0 = Force DTR# output HIGH (default).
Logic 1 = Force DTR# output LOW.
MCR[1]: RTS# Output
The RTS# pin is a modem control output and may be used for automatic hardware flow control by enabled by
EFR bit-6. The RTS# pin can also be used for Auto RS485 Half-Duplex direction control enabled by FCTR bit-
3. If the modem interface is not used, this output may be used as a general purpose output.
Logic 0 = Force RTS# HIGH (default).
Logic 1 = Force RTS# LOW.
相關PDF資料
PDF描述
GSM10DRUS CONN EDGECARD 20POS DIP .156 SLD
MLF2012A3R3J INDUCTOR MULTILAYER 3.3UH 0805
XR20M1170G16-0B-EB EVAL BOARD FOR XR20M1170 16TSSOP
XR20M1170G16-0A-EB EVAL BOARD FOR XR20M1170 16TSSOP
723280-000 BOOT MOLDED
相關代理商/技術參數
參數描述
XR20M1170G24-0B-EB 功能描述:UART 接口集成電路 Supports M1170 24 ld TSSOP, SPI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR20M1170IG16 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR20M1170IG16-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR20M1170IG16-F 制造商:Exar Corporation 功能描述:IC SGL UART 16MBPS 3.63V 16-TSSOP 制造商:Exar Corporation 功能描述:IC, SGL UART, 16MBPS, 3.63V, 16-TSSOP
XR20M1170IG16TR-F 制造商:Exar Corporation 功能描述:UART 1-CH 64Byte FIFO 1.8V/2.5V/3.3V 16-Pin TSSOP T/R 制造商:Exar Corporation 功能描述:XR20M1170IG16TR-F 制造商:EXAR 功能描述:UART 1-CH 64Byte FIFO 1.8V/2.5V/3.3V 16-Pin TSSOP T/R
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*